Find professional window and door services in Brookvale

We have a task to replace 6 Garage doors in a block of industrial units. We just need someone to install the doors. The new doors do have electric controllers, but we do not need the controllers to be installed. Happy with the manual operation at this time. Each door is 3600 W x 4300 H Your job is to remove the existing garage doors prior to installation and install the new ones. You can quote to dispose of the ole doors all as well, but we are prepared to take care of that part of the task. You can leave the old doors on site.

We have 3 single doors we’d like to instal, and one double door

I’m replacing old locks/levers on 3 internal doors with new Gainsborough Matte Black Choice Harper Square Privacy Lever Sets (60mm backset, 54mm bore, 25mm edge bore — I’ll supply the handles, latches and instructions). The old hardware has already been removed. Scope: 1. Patch 2 door edges: two doors had mortice locks, leaving rectangular cavities in the door edges. These need solid timber infill blocks, glued and packed tight, planed/sanded flush — the new 25mm latch bore and faceplate screws go straight through the patched area, so it must be solid. Please bring suitable timber and adhesive. • Door 1 (bathroom): cavity approx. 100mm high x 17.5mm wide, door thickness 34.8mm • Door 2 (second bathroom): cavity approx. 57mm high x 16mm wide, door thickness 34mm • Please verify cavity depth on site — I haven’t measured it 2. Drill new holes in all 3 doors: 54mm face bore at 60mm backset + 25mm edge bore. Third door (bedroom, 34mm thick) has no cavity — drill and fit only. Note: all 3 doors have existing old spindle holes (~14–23mm) that overlap the new bore centre, so a hole saw pilot bit won’t have material to engage. You’ll need to clamp a sacrificial board over the face to guide the hole saw, or use a lock installation jig. The old holes fall entirely within the new 54mm bore and will be drilled away. 3. Install the 3 lever sets including latches and strike plates, chiselling strike plate recesses in the jambs as needed, and confirm doors latch and the privacy function works. Doors can stay on their hinges. Painting/finishing not required. You’ll need a 54mm hole saw, 25mm spade/auger bit and chisels.

We are a childcare centre and need handles on 2 internal doors moved higher up so children cannot open the doors. The locks are not needed. We need an invoice.

I need a solid door purchased and installed in this area here Measurements in photo I have the handle, I just need the door supplied.

I need help to trim off 20mm at the top & at the bottom of a door, then install handle and hinges from old door to new door and put the new door in the bathroom.

I need to: 1) Trim 20mm off the door at the top and 20mm off at the bottom of a standard Bunnings' door (Flush Internal Honey Comb) 2) Remove old door's handle and hinges and put into new door (the new door doesn't have any holes yet) 3) Apply handles and hinges in the new door and put it up in the bathroom.

We have an internal sliding door which sits inside a door cavity. The track has never worked well and recently completely fell off the wooden frame. The sliding door now does not work whatsoever with no track in place. We will need a completely new sliding door track sourced and installed (we will not be using the old track). The previous track was not installed very well. The door sits inside the wall cavity so the only way to replace the track is to cut a hole in the gyprock wall to install the new track, re-plastering and paint.

Need a hinge fixed for an internal bedroom door Door otherwise fine

Drill hole and attach ring door bell

The sliding doors to my backyard has a latch and both have stopped working. May need to be replaced. Unsure.

We need to get our industrial door reattached and retouched around the edge with plaster.

Window repair for double-hung sash window - View all the details of this offer: https://www.airtasker.com/offers/01JMB5Q3ESWMR9T2KR7DY298K2

Window cant stay open. Seems the one that's holding the section is damaged. Please see photo below. Looking for someone who can do today.

Folding bill fold door has come off its rails It may need new spring and parts

I could this myself but just run out of time. Should be pretty easy task.

Replace mental grille on door

Sliding door doesn’t close properly and there is a gap so that the lock doesn’t work

Hi there we need a garage door painted inside and outside this weekend

Pick up the new door from brookvale (paid for), take to Wentworthville. Remove the old door then fit the new one. Stain and install the old door handle onto new one