Hire reputable rangehood installation and ducting services in NSW

The cuurent Boshe 70cm needs replacing, I have bought Serius undermount rangehhod SL927 which is 52cm, I have not bought ducting as yet but can. 1. The existing needs to be removed 2. Install 16mm Malamine board, bracket to the sides. (I have purchased the board) 3. Cut out as 4. INstall new serius rangehood to existing ducting or new serius ducting maybe required 5. looks to go into ceiling or roof

Install a new rangehood for our kitchen

install ducting and rangehood. use existing hole outside of house for ducting outlet. cut new hole internally highlighted in yellow. connect ducting from inside to outside physically install new rangehood. i will arrange electrician to connect power. suggest a cheap rangehood for me to purchase

I need someone to install an exhaust duct for my existing kitchen rangehood so cooking smoke and air can vent outside.

Need old rangehood to be removed. New ranghood needs to be replaced. No Air duct. But need to drill 120mm hole in plywood, as per instructions.

Need to install new rangehood with duct. Duct to run through roof cavity and down the eaves. This run is 2-3m to the eaves. Easy access I need you to supply duct and external eaves grille

Need someone to install 60cm fixed range hood. No need to remove old one as it has already been taken down.

Install a new Bosch Rangehood. It will also require cabinetry or installation kit work.

Need 3 holes drilled into a glass splashback for rangehood installation. Urgent.

Need new rangehood installation in kitchen ..need to cut hole in wall also for ducting ..Starta asked me to submit sketch by someone professional installer for actually installation plan for approval to make hole in external wall first ..if someone can help me

Looking for a competent and experienced handyman to install a new undermount rangehood into existing kitchen cabinetry. The existing opening is larger than the new rangehood, so the job will require some modification/engineering to the cabinetry to create a neat, secure fit and professional finish. Ideally looking for someone experienced with kitchen cabinetry and rangehood installations who can assess the best way to adapt the existing opening. Please only respond if you’re confident with this type of work and have the appropriate tools and experience.

I need an old 60cm recirculating rangehood removed and a new Westinghouse WRF610SA (fixed, recirculating) rangehood installed in its place. Because the rangehood sits directly above an existing gas cooktop, the installation requires some minor carpentry modifications to meet the legal 650mm Australian gas safety clearance (AS/NZS 5601.1:2022) — the current clearance is only 585mm. The job involves: Removal: Disconnecting and removing the old 60cm rangehood (recirculating setup). Shelf Adjustment: The mini cupboard above has a horizontal width of 60cm and a depth of 30cm. The internal base shelf needs to be unscrewed and raised upward by roughly 8cm to 10cm, so the final clearance to the gas cooktop is at least 650mm (please confirm this measurement before final fixing). Door Trimming: The two mini cupboard doors will need 8cm to 10cm cleanly trimmed off the bottom edge to match the raised shelf. Important tool requirement: Because the kitchen cabinets are laminate over particleboard/chipboard, please use a clean-cutting circular saw or track saw with a fine-tooth blade to prevent the laminate edges from chipping or splintering. Mounting: Securing the new Westinghouse WRF610SA onto the newly adjusted shelf and setting it to internal recirculating mode (2 carbon filters). Note: The new unit is a standard plug-in unit (no hardwired electrical work needed) — it plugs into the existing power point.

I need to have range hood to be removed and installed at my existing kitchen give me the price for installed

Install rangegood in my kitchen

Need to install rangehood in the kitchen width is 600 mm, need to make hole in the roof.

Replace & dispose of old gas cooktop & rangehood. Straight swap in of new 60cm gas cooktop & rangehood. Available on the weekend only.

Electrician will provide Electrical Power Provision. You need to help to install the rangehood. Duct can be put through the back wall fence to face the open sky (1.5feet gap between my fence and neighbour fence). Refer to the rangehood model and and photo of the marked install area. In photo on top BBQ fence the light will be removed and power provisioned and connectivity will be provided by the electrician. There is a single phase power subboard under the bbq cupboard from where the power is coming through behind the wall fence. Here is the product link which is already delivered at my place. https://devanti.com.au/products/devanti-range-hood-commercial-rangehood-bbq-hoods-kitchen-alfresco-canopy-1500mm?srsltid=AfmBOopLn3QYoWKoIHgyG8NhZUBDnqNoxe6dgVsYgTlbliWxZs7b87qx

I need an experienced handy person to install a re-circulating rangehood into an existing kitchen cavity. The rangehood is re-circulating (no ducting or electrical work required). The overall objective is to install the rangehood, but there are some anticipated steps (but I will require you to do all things necessary to install the rangehood within the agreed price): 1. The cabinetry has 2 ‘filler’ blocks obstructing the rangehood slot. These need to be cleanly removed without damaging surrounding cabinetry. I’m unsure how they are affixed to the surrounding cabinetry (by screws, glue or other). You may need to temporarily remove and re-hang the cabinet doors to get proper access. 2. Drilling new holes through the cabinet shelf, in order to align with the top of the rangehood, and securely mounting the rangehood unit. I will provide the rangehood and its standard mounting screws and the access to the power outlet, but cannot supply any tools or other materials. I do not require any ducting/electrical work, cleaning or removal of old rangehood. I’m looking for a total fixed-price quote to complete the installation.

I need someone to install the canopy rangehood for new kitchen

Looking for someone with kitchen cabinet experience to help install a new 900mm x 300mm sliding rangehood. The new rangehood vent area is larger than the existing one, so the surrounding cabinetry will need careful adjustment to accommodate it. We need someone who can handle both the installation itself and make the necessary modifications to the existing cabinets, keeping everything looking neat and intact. The cupboard is 300 deep, the current air vent area is 200, but new one is 300 deep, so the lower shelf area needs to be adjusted out effectively. New Range hood is a Westinghouse Model Number: WRR904SB, dimensions attached in image.