Find an experienced plumber in Northmead

1. Fix new kitchen tap at the kitchen sink 2. Remove existing shower head and fix new one 3. We will supply tap and shower

Earlier this year a plumber replaced our shower heads in both of our bathrooms. Since that time, hot water flow to the shower heads has been later. The same plumber remove flow inhibitors from the shower head which increased flow somewhat but not to the previous level. That plumber has now left the business, and as winter has come, hot water flow is not sufficient, particularly in the main bedroom shower. We'd like to see if there's a solution within the current framework to increasing hot water flow.

Someone available now. Gas needs to be re lit by handyman or person. It is very easy it has instructions inside panel it takes 40 seconds to re light. See photo.

I have some plumbing work at a granny flat. Scope. Fit off (product supplied) kitchen mixer Toilet basin mixer Bathroom basin mixer Bath hot/cold spindles and spout Shower rail, head, and spindles Disconnect existing gas hot water storage heater and remove from site. Supply and install new electric hot water storage heater (need you to supply 125L). Cap off gas from granny flat. So far we have disconnected and removed existing gas cooktop but please cap off at valve in cupboard next to oven. Please quote on this. Must be for this Monday 7am. Quote separately for supply electric hot water 125L unit (I will pay for this directly).

Need to replace 1 x laundry tap connected to washing machine. Tap will be provided Would need to move washing machine to install tap.

Replace toilet paper holder, install towel hook, replace toilet seat cover, fix screen door hinges, replace shower heads

I only have hot and cold isolation valves under the laundry sink for the mixer, and there is no washing machine connection point. I need a plumber to: • Use the existing cold-water line under the sink • Install a fixed, dedicated cold-water outlet for the washing machine • No external tap required • Ensure the outlet is positioned safely and complies with NSW plumbing standards

Install new basin, cut engineered stone to fit new size and reconnect to existing plumbing.

We have noticed that when our water tank is empty that flushing of toilets etc does not automatically divert to town water. There is no diverting switch/ tap. We live in a duplex and our adjoining duplex neighbour reported the same issue. We require a plumber to create a diverting mechanism in situations where the water tank is empty.

I would like to have a hot water tank timer installed please

Unblocking Partially Blocked Toilet & Replacing 2 Washers

Broken pump. Need replacement

The little outlet under the sink needs to be closed as water gushes out from it. In the laundry area.

I have got a toilet roll holder and towel rail which i want to install in my bathroom. i am worried that i might crack the tiles cause it's Porcelain.

Install the tap in kitchen sink

Quote to convert existing garage into laundry (washer, dryer and sink), bathroom (toilet, shower vanity basin) and kitchenette. Also need to relocate existing HWU to a temporary location. works is slab on ground.

We need help with connecting our fridge to water. The sink is next to the fridge, but we would like the water tube to come through the wall so it is not visible. We have the filter and some of the tubes as shown in the photos.

please see attached photos

Refer to photo. Require Jetta.

hi We need an industrial plumber urgently for 5 small tasks: • 10mm spigot for the sampling point is required, • A 2-pin and a 7-pin amphenol plugs are required for the autosamplers to be connected to the flow meter, • A 120mm incoming vent is required on the GT and it must exit the building above the roof line. • A 120mm exiting vent is required on the GT and it must exit the building above the roof line. • Backflow devices required on the hot and cold water within the bunded area used for cleaning the trade waste area. More explanation: 1. A 10mm spigot is required on the sampling point for the connection of auto-samplers. 2. 1 x 2-pin and 1 x 7-pin amphenol plug socket for connection of the autosampler to the discharge flow meter is required. These can be obtained and fitted from the supplier of the flow meter. 3. 120mm incoming vent pipe for cross flow ventilation from the grease trap exiting external to the building 1 meter above the roof is required. 4. 120mm exiting vent pipe for cross flow ventilation from the grease trap exiting external to the building 1 meter above the roof is required. 5. Backflow devices for the hot and cold water within 5 meters of the TW area are required.