Find a local heated floor installer near you

I need an electrician to install the following in my bathroom - Thermogroup Thermonet 150W/m² Under Tile Heating with Wi-Fi Thermostat at 4.5m²/675 W. - IXL White Tastic Luminate Single 3 in 1 Bathroom Heater, Exhaust Fan And Light. My previous one was not ducted. This one says it can be ducted through the wall (which is timber). - Finish off two power points (cables already installed) Bathroom is on second story and there is attic space above. I also need a new standalone motion sensor at front door (Clipsal Infrascan Outdoor Motion Sensor IP66)

We have two underfloor zoned heating systems, Comfort Heat and Devex. Want to program them to come on in the morning and evening and eco temp during the day.

I need the old floor registers removed and the openings patched so they match the surrounding timber floors and tiling for the bathroom and kitchen area. I have the matching tiles, but need to purchase matching timber.

Looking to update our heated floor control panel - it is a speed heat model as per attached photo If it can't be updated - the would be looking to program it or get instructions of how to program it to a specific time of day

Honeywell home under floor heating controller not working repair/ replace if needed + parts price extra

New Underfloor heat mat damaged in 5 places. Needs to have joints and repair patches in these areas. Clear floor space to work in, need it sorted before screed.

Installation of Tile Backer Insulation Boards (1200mm x 600mm x 6mm) across a concrete slab. Boards will cover a area of approximately 50m2. These boards need to be screwed using 25mm fibre cement screws into the concrete slab below. A high strength poly-urethan tape will then need to be taped across the joints of the boards. Note Boards, Screws and Tape will be supplied. This quote request is for the installation and waste removal cost only.

I require a handyman to get under the house and remove the heating ducts. Cutting the tape and removing the boots from floor vents and return air box. I am able to help, I have a fear of confined spaces hence the need for help ! Should be around an hour and a halfs work.

I'm renovatin the bath and Ensuite. Need a quote to intall the heating system before tiling

I have a floor heater vent that has broken into the floor and needs to be sealed up. I have attached a photo of one of the other vents to show the design.

Underfloor heating in our bathroom is no longer working and the thermostat won’t turn on anymore.

Underfloor hydronic heating system needs service. Has Immergas boiler which shows E6 fault .system is not functioning properly

I am replacing an old Warmup floor thermostat TH115-AF with a WT01. All it needs is floor & power wires attached & installed back into the wall plate.

The underfloor heating system worked properly last year. Earlier this year, during renovation, the original Honeywell mercury thermostat was replaced with a Siemens electronic thermostat (DMM310/MM). Now, when turning on the heating, the boiler fails to start. Professional assistance is needed to commission the system and start the boiler.

Repair x2 underfloor bathroom heating

I cant seem to get the monitor to work

My gas heating has been removed , I want to get the heating vents filled in. They have already been blocked but want them to be flush with current floor. Carpet flooring will be replaced over the top so just needs to be sturdy and flat. There are 6 vents in total.

Program my Amuheat controllers. I have tried this and have kind of got it right but need someone who has done this before

Screed to be applied to inscreed heating elements prio to tiling

Hey guys Just wanting someone to come and potentially have a look at our floor heating system and see if they can diagnose why its not working, I think it may be a thermostat issue but im not too sure, as far as I can gather from the previous owners, the heating stopped working when they replaced the slate on the floor, although the system is an "inslab" heating system so I dont believe they have broken a wire as the circuit breaker doesn't trip or anything like that, im unsure how much it will cost to just run a few checks, obviously being in slab it would be a bit hard to check the actual wiring but im unsure how it all works