Find an experienced handyman in Salisbury QLD

We have a HPM ceiling fan with wall switch dial for 3 speeds. Wanting to get a remote instead so can switch speeds while in bed.

Installation of one of the Dagood letterboxes. Needs a small section of grass cleared and cement laid and then attached as per instructions.

I would just like a foldable clothes line put up on my deck

I need someone urgently to cut down 4 x Stratco Ambient outdoor blind cassette/headboxes / blind components. Installation is already arranged. This task is for the cutting only. The blinds have been supplied slightly too large / too tight for the reveal openings. Stratco has advised that the manufacturer can speak directly with the person doing the cut to guide the process if required. Approximate cuts required: - Blind 1 / left side: received cassette/headbox 2986 mm. Requested adjusted length 2976 mm. Approx. 10 mm cut. - Blind 2 / front left: received cassette/headbox 4005 mm. Requested adjusted length 3996 mm. Approx. 9 mm cut. - Blind 3 / front right: received cassette/headbox 2949 mm. Requested adjusted length 2941 mm. Approx. 8 mm cut. - Blind 4 / right side: received cassette/headbox 2989 mm. Requested adjusted length 2979 mm. Approx. 10 mm cut. The cuts need to be accurate and clean. Please only apply if you have the right tools and experience cutting aluminium or similar blind/awning components. Important: - Final measurements must be checked before cutting. - No cutting should occur until the final cut measurements are confirmed. - Stratco/the manufacturer can speak with you before cutting if needed. - I can provide photos and the measurement table. - I can potentially bring the blinds to your workshop if that makes the job easier. - Job is urgent. Please include in your offer whether you have experience cutting aluminium cassette/headbox, awning, or blind components.

I need an experienced blinds installer / handyman to cut down and install 4 x Stratco Ambient outdoor blinds. The blinds have been supplied slightly too large / too tight for the reveal openings. Stratco has advised that the manufacturer can speak directly with the installer to guide the cutting process if required. Scope: - Attend site and inspect the 4 blinds and reveal openings - Confirm all measurements before cutting - Speak with Stratco / manufacturer if required - Cut / adjust the cassette/headbox/blind components as needed - Install the blinds within the reveal openings - Ensure the blinds operate properly after installation Approximate cut dimensions: - Blind 1 / left side: received cassette/headbox 2986 mm. Requested adjusted length 2976 mm. Approx. 10 mm cut. - Blind 2 / front left: received cassette/headbox 4005 mm. Requested adjusted length 3996 mm. Approx. 9 mm cut. - Blind 3 / front right: received cassette/headbox 2949 mm. Requested adjusted length 2941 mm. Approx. 8 mm cut. - Blind 4 / right side: received cassette/headbox 2989 mm. Requested adjusted length 2979 mm. Approx. 10 mm cut. For context, the received cassette/headbox lengths appear to be between 2 mm and 8 mm larger than the narrowest submitted opening measurements and do not appear to include a separate fitting tolerance / deduction for reveal installation. Important: The above measurements are provided to explain the job only. The successful installer must take their own check measurements on site before cutting. No cutting should occur until the final cut measurements are confirmed and, if required, discussed with Stratco / the manufacturer. Please only apply if you have experience with outdoor blinds, roller blinds, awnings or similar, and are comfortable accurately cutting aluminium cassette/headbox components.

Install shower screen. Corner shower, two panels fully framed.

Would like to dig up this clothesline anchor. About 2 feet deep

I need someone to install new ceiling fan.

Looking for installer for outdoor insect mesh blinds/screens – Brisbane Hi, I am looking for an experienced installer to help enclose the alfresco / outdoor living area at my house in Brisbane to reduce flies and insects while still allowing airflow. I am considering purchasing the outdoor blinds/screens separately myself, so I am primarily seeking installation quotes. However, I am also open to supply-and-install options if available. The area to be enclosed is the ground floor “Outdoor Living” area and includes approximately: • Front/main opening: 7.1m wide • Side opening 1: 3.0m wide • Side opening 2: 3.0m wide Total approximate coverage required is 13.1 lineal metres, subject to site measure. I am interested in insect mesh zip-track / side-retained outdoor blinds/screens with proper side channels and bottom seals to minimise gaps for flies and insects. For the 7.1m front opening, I would appreciate advice on whether this should be split into 2 or 3 separate screens. For one of the side openings, I may also need an access solution such as: • hinged screen door • sliding screen door • double doors or another recommended option. Please let me know: • whether you offer installation only or supply + install • experience with zip-track / outdoor screen systems • estimated lead times • whether you can assist with site measure and product recommendations • what is included in your quote (tracks, pelmets, posts/framing, hardware, seals etc.) Happy to provide photos, plans and measurements. Thanks, Panashe

This blind is held by this ring. Ring holding the blind has broken due to getting rubbed against the metal wire as seen in picture.

Need a few roller blinds fixed about six to 8 blinds price is per blind

The very old letterbox has been removed however the metal bracket that secured it into the ground remains. I need this cut back so that it doesn’t stick out of the grass. OR can completely remove the concrete base. Either way!

Looking for a licensed electrician to install a ceiling fan in our kitchen. We already have the fan. Standard ceiling height, no existing fixture in place.

Looking for a licensed plumber to disconnect and remove our existing kitchen sink and tap in preparation for a new benchtop and sink installation. Details: Existing sink and tap need to be completely disconnected and removed. Sink is a top-mount style (standard single bowl). Benchtop will be cut and replaced after removal by the stonemason. No need to reconnect anything — this task is just for safe removal and capping off water lines. Easy access, single-storey home in Salisbury, QLD. What’s required: Licensed plumber preferred. Bring your own tools. Must ensure water lines are safely capped and sealed. Clean up work area after removal.

Replace doorknob on bedroom door. I have purchased a new doorknob, however when I went to install, I realised the cross bore hole is smaller than the current standard doorknob sets, meaning the latch does not fit through the hole. I either need the hole expanded to fit current doorknob standards and the doorknob I bought installed or a doorknob purchased and installed that would fit the current hole.

Install cold water to kitchen sink. In grey water outlet.

Please install a doggy door in a screen door

2corner kitchen cupboard hinges need replacing

Need the 2 corner kitchen cupboard hinges replaced

Remove 2 existing outdoor blinds. Install 3 outdoor Shade screen Bistro Blinds on deck. https://bistroblinds.com.au/wp-content/uploads/2016/11/PDF-Bistro-Instructions.pdf