Hire a trusted gas stove repair and installation service near you

Need new gas top cooker connected to exisiting connection. Has been installed to bench top (although can lift up for access if needed) the pipe from the cooktop and the main in let is only 300mm away from each other. We are on tank supply (LPG)

70cm gas stove need replacing . I am sourcing a 70cm omega model. I need an urgent installation today.

Stovetop gas supply gets randomly interrupted/disconnected, causing the burners to extinguish while in use.

Gas stove ignition in two burners are not consistent … otherwise gas flow and flame is normal … no other issue ..only two burners not lit up so I need to use lighter ….may be basic service

Electrician/Plumber to replace/install rangehood and oven as well as remove gas stovetop and convert to electric in apartment unit. Switch board located at left side of main door in wide picture attached. Electrician to remove Oven and Rangehood. Plumberto remove old gas stove top

I'm needing a gas plumber to changeover a gas cooktop. looking for a local plumber area for ongoing work. I have a small install business with re occurring local work

Renovating my kitchen and need a licensed plumber and gasfitter to: - Disconnect kitchen sink hot & cold water and cap off safely - Disconnect sink waste and seal the pipe - Disconnect gas cooktop and cap off the gas line Requirements: - Must hold BOTH a QBCC plumbing licence and a Queensland gas work licence (please include both numbers in your offer) - Gas compliance certificate supplied for the gas work A separate fee/task will be arranged to reconnect everything once the new benchtop is in. Photos of the sink cupboard and cooktop attached. Located near Beenleigh. Flexible on timing.

I’m getting a new bench installed tomorrow and seeking quotes for a plumber / gas fitter to install a new gas stove and sink + tap. Stove is 60cm standard size. Sink is 540mm x 400mm (standard size for one bedroom). I’m needing it properly installed with appropriate sealing. Bench guys coming tomorrow so ideally you can come mid afternoon. However may seek your availability on Friday also in case they’re running late.

Looking for a quote from a plumber who is licensed to remove current 60cm gas cooktop (glass) and install new stainless steel cooktop.

I need to replace an old gas cooktop. I have purchased a new cooktop and need it fitted by a qualified plumber/gasfitter and a compliance certificate issued.

Need a licensed electrician to remove the pictured rangehood/cooktop/oven.

I need a licensed gas fitter to install a new 60cm 4 burner gas cooktop. The cooktop is already purchased and on site (Esatto ECG604WS from Bunnings, natural gas, cutout 560 x 490mm, manual in the box). It replaces an existing Electrolux 60cm induction cooktop and fits the same benchtop cutout. - Existing gas supply is capped off in the cabinet under the sink (from a previous gas cooktop). Photo attached. - Remove the induction cooktop and fit the gas cooktop into the existing cutout. - Connect gas, leak test and commission all burners. - The induction cooktop is hardwired, so it needs to be safely disconnected, and the gas cooktop's electronic ignition needs a 240V power point under the bench. Please confirm if you can do the electrical part or if an electrician is needed. - Provide a Victorian Compliance Certificate on completion. Please include your Victorian gasfitting licence number in your offer. Payment through Airtasker only. Please only offer if you can arrive on time with all tools, including a gas tester. Photos attached.

We would like to replace the 60cm 4 burner gas cooktop, with the new one. Dispose the old one. Due to regulation need to be installed by licensed to install gas cooktop and an invoice

I bought a 90cm ASKO gas stove. The hole in my bench is slightly too small, some stone needs to be cut and possibly a little timber. Also need to connect the gas. Hole dimensions 83.5cm x 47.5cm Stove base dimensions: 85cm x 47.6cm

## Licensed Gas Fitter Needed – Gas Cooktop Installation (Kogarah, NSW) I’m looking for a **licensed gas fitter with a valid NSW licence** to help install a new gas cooktop at my house in Kogarah. **Please do not apply if you do not hold the appropriate NSW gas-fitting licence.** **Preferred date:** Saturday, 17 October 2026, during the day after 12pm. **Parking:** Driveway parking available. ### Scope of Work 1. **Remove existing gas cooktop** – I can assist with removal and disposal. 2. **Install new gas cooktop** – Electrolux 60cm Natural Gas Ceramic Cooktop (Model: EHG635BE), already purchased. 3. **Enlarge existing benchtop cut-out** – The benchtop is laminate, and the existing cut-out needs to be enlarged slightly to accommodate the new cooktop. - New cut-out width: 560 mm - New cut-out depth: 490 mm I’m a qualified carpenter and can assist with the benchtop modification using a jigsaw and circular saw, if appropriate. 4. **Connect and safety-test the cooktop** – Complete the gas connection, installation and required safety testing. Existing gas and electrical outlets are available below the cooktop. ### About the Job I’m a qualified carpenter and happy to assist with suitable preparation and other tasks to help get the job done efficiently. **I don’t think the job will take too long**, especially as I can help with the removal and benchtop modification. All gas-fitting work must be completed by an appropriately licensed professional. Please get in touch if you hold the required NSW licence and are available on the preferred date. When responding, please confirm your licence, availability and quote for the job. Thank you!

I need the gas disconnect for an oven stove please see picture

The spring in the bathroom sink plug is no longer releasing. I pushed it down, but it is now unable to pop back up. The cooktop ignition is also not turning on, although the gas is still working.

Looking for an appropriately qualified/licensed appliance repairer or gas fitter to attend a short-term rental property in Windsor, Brisbane to diagnose and repair a gas cooktop ignition issue. Issue: - Gas is flowing to the burners normally - Burners are not electronically sparking/igniting - Guests can currently light the burners manually, but we need the ignition repaired - Make/model can be provided once confirmed We would like someone to attend as soon as possible this week, diagnose the fault and repair it where possible during the same attendance. Potential issue may relate to the ignition system, spark module, electrode or microswitch, however this will need to be professionally diagnosed. Please include in your offer: - Call-out/diagnostic fee - Your availability - Relevant licence/qualifications - Whether you can supply common replacement parts if required Please provide photos/details of the fault and completed repair for our property records.

I’m looking for a qualified and licensed gas fitter/plumber to replace my existing gas cooktop. The job involves: * Safely disconnecting and removing the existing gas cooktop * Installing and connecting the new gas cooktop * Ensuring everything is safely and correctly fitted and compliant * Removing/disposal of the old cooktop I’m looking for someone who is properly qualified and licensed to carry out gas work. Please include your total estimated price for the job when making an offer, including removal of the old cooktop if possible.