Find experienced local fencing contractors in Mosman

pool gate glass panel was smashed and need replacing - need to quote on supply of new panel (6mm glass thickness) and installation (can use existing hinges and closing bolt fixtures) - no need for broken glass disposal - it was already cleaned . Panel measurements - please note those are taken by me - pictures as reference - 6mm thick - 1162mm tall - about 920mm wide please refer to pictures - but it need to be on site measured before ordering panel ... Hinges x2 and locking bolt x1 - existing to be reused address of the job 1 Bullecourt Ave Mosman NSW Please ask if need more details - thank you

I have an old fence which needs to be secured and one part has come away which will need to be put back together or replace the latticeor replaced.

New side of fence requires painting to match existing fence. Approx 35 metres. First photo is the new part of the fence. Second photo is the existing fence.

We need a fence height extended to comply with swimming pool regulations. The fence length is 9m. We also require an additional fence strut inserted to provide additional strength

Remove old clothesline and install new clothesline, take down awning, nail in part of the fence which is coming off

Screw timber fence panels 3-6 pieces

Replace about 3m of chain wire to fence and gate and supply gate lock need to supply materials

Need a new back gate built - see photos attached for existing gate. Height to stay same

Our puppy escaped over our low fence this morning. Looking for someone to help build a temporary fence of some sort to secure the yard. Approx 5 linear metres required to be secured. Will pay materials on top of quoted amount.

Fence needs to be secured against brick wall

we need latch and hinge replaced on pool fence door, current latch does not comply with AS1926 requirements.

I require 17m in total lap and cap fencing. Of this total 10m is to be 2.4m high and 7m to be 2.1m. (10x24. + 7x2.1) Lap and Cap on finish on both sides as my neighbor and I both want the good finish. There is a iron 1.2. fence with iron polls which can be used by putting in a sleave post on top so we don't need to core trill across all 17m. Account for core drilling 2/3 posts at max. Require painted. Paint will be supplied.

Single fence around garage has become loose at ground level. Also some slats need repairing.

Build and install lattice, trim away current hedging in the way.

Need somebody to cement render brick perimeter fence inside and on street side. Approx 30 metres both sides. Small section of the brick wall needs to be repaired or replaced, . (See photos ) Wanted done ASAP. Must have rendering and bricklaying experience.reference essential. Make an offer.

Repair broken side gate/ latch and measure and install new pool fence gate inside classroom.

Looking to replace part of a color bond fence with a gate of the same material. Dimensions of current fence 800 mm W x 1720 mm H. In the pictures, the first two are the front of fence, there is a Tesla charger that will be moved. The second two are of the inside of fence. Unsure of cost so putting $5 placeholder. Not urgent so we are flexible with timing

Install timber lap and cap fence with palings both sides as a privacy screen from our pool. 1.6m wide and approx 2.1m tall. The fence will run perpendicular from our side fence and will join our terrace. You will need to remove an existing glass pool fence panel. We then also need a boundary fence 5m long x 1.8m high also lap and cap with palings both sides. The boundary fence will need to be installed on the top of a sandstone retaining wall so you will need to set metal posts in the wall.

We have two fences on each side of house that need hammered back into place (we do not have the nails) one is a large panel while the other has a few boards that have fallen loose. We also have a fence out front I’d like to get hammered back into place.

Hi There  Please quote on pool fence gate glass panel replacement  Please note - we are gardeners and we smashed our customer glass panel … Address of the customer / broken pool gate fence : 1 Bullecourt Mosman  Approx measurements: - glass thicknes 0.5cm - panel width 94cm  - panel hight 116cm - please note above measurements are approximate and you will need to take your measurements before ordering/installing the panel 2x existing hinges and gate latch to be used on new glass panel  Please emai quote to: [email protected]  Invoice to: Vision Horticulture Services  Thomas Kwasik  U4 / 421-473 Pacific Hwy Artarmon  Please let me know if you need anything else  Kind Regards Thomas