Find trusted local electricians in Baulkham Hills

I have 3 decorations lights need to be installed, one of them is outdoor

Gas water heater leaking. Hot water supply is normal without any noise or gas smell.

4 GPOs and switches are loose and damaged, need to repair, tidy up or replace

I have issue with the phone line from wall which should be transferred to nbn connection

commercial outlets stopped working

Hi, I'm looking for a licenced electrician to get a PowerPoint installed in my garage to be used for the garage gate motor and couple of more things like fan installing..

1.Bathroom Switch not working slightly moved 2.Another power point not working 3. few downlights needs replacement

I have Jinko Solar 370W solar panels with Growatt 5kVA Single Phase Inverter and it has stopped working, need someone to take a look and fix it.

The wiring for the water heater at the power board needs to be done to off peak. Currently on on peak. Also need a timer in that so the water heater only operated off peak during the day when my solar is on

We have an old split ac that needs to be taken off and disposed. Looking for help. The electrical disconnect has already been done. Have a van - sprinter. can be used if needed, Flexible on timing. Pictures below

Cbus2 lights randomly turning on Need an expert review to identify root cause . Only expert cbus2 technician Clipsal cbus2 blue fee is for root case identification

I need many electrical works for my new house such as LED lights , run induction cooktop , internet cables …

Install 9 Downlights + Reposition 5 Powerpoints + New Fridge Powerpoint Job Scope: 1. Install 9 LED Downlights (Plug-in Type) 4x Downlights for the Kitchen 5x Downlights for the Dining Area All downlights have power plugs (supplied) Ceiling is accessible (roof cavity access available) Downlight positions are marked – see black circles in the attachment Red circle markings indicate existing surface mount LED lights 2. Reposition and Replace 5 Kitchen Powerpoints- Grypock wall Slight relocation needed for better alignment (not far from original spots) Replace with new powerpoint plates (supplied) 3. Install 1 New Powerpoint for Fridge- Grypock wall Install 1x standard powerpoint for fridge See blue square marking in kitchen area (attachment) Powerpoint will be supplied Requirements: Must be a licensed electrician Experience with retrofit lighting and light roof work Clean, neat, and professional finish preferred

. Can inspect and then quote 1 Downlight needs to be replaced. 2 Light Dooms to be changed 2 batch exhaust fans to be changed

My switch boards has hot water used to connect to control load. Recently, due to the solar battery installation, it changed to main load. Based on latest analysis of our electrical plan, we think it’s better to change it back to control load during winter time. I observed how the electrician changed to main load while battery installation . It should be a less than 10minute work.

Old intercom is connected, needs to be replaced and a new door bell wired up and then fit off to the wall. Also 2x light fittings to be replaced with new fittings. Both at low level in a storage area - approx 2m AFFL (no photos of the lights sorry)

I need a wall socket for NBN, please help me to install a cable from external into my house.

Error code 99 is flashing on my bit water system

Need someone to just dig trenches. Both side of the driveway. In total 18m length.

We’re looking for a licensed and experienced electrician in Sydney to help diagnose and fix a recurring issue with our home’s electrical system. The issue: • One phase of our multi-phase system is tripping the breaker (RCD), usually ~15 minutes after switching it on. • This started after heavy rain last week and has persisted even in dry conditions. • A similar issue occurred in another phase previously and was traced to water ingress in a hidden junction box. • We’ve ruled out appliances—fridge, dishwasher, and microwave are unplugged—but the breaker still trips. • There’s no visible water damage or burnt smells, but we suspect moisture is still trapped in a junction box, conduit, or wiring insulation. What we need: • Urgent on-site inspection to trace the fault in the affected circuit. • Identification of the hidden junction box (we have electrical blueprints to help locate it). • Insulation resistance testing (megger) or circuit tracing tools may be required. • Fix the fault—most likely involving sealing, replacing, or rewiring affected components. Please bring the necessary tools and safety gear. Access to electrical drawings will be provided. Ideally looking for someone available ASAP. Let us know your availability and experience with similar water-related electrical faults.