Find a reliable cooktop installation and repair service in NSW

Omega OI64BA cooktop installation

Replace the old cooktop with new. The size is 90cm and no cut out should be required.

I need an experienced stonemason / benchtop installer to enlarge an existing cooktop cut-out in my kitchen stone benchtop so a replacement cooktop fits. The new cooktop is a few cm larger, so only a small increase to the current cut-out is required

Gas company has attended and repaired the outdoor gas valve and confirmed gas supply at the meter. The gas cooktop ignites normally (spark and clicking sound present), but there is no gas flow to the burners. I need a licensed gas plumber to: • Check and open the cooktop isolation valve (if closed) • Purge air from the internal gas line • Confirm gas is reaching the cooktop and test ignition This is an existing cooktop, not a new installation. Property is owner-occupied. Please quote for inspection and commissioning. Any additional work to be discussed before proceeding.

Licenced gas fitter to disconnect existing cooktop and install new cooktop

After 3/4 days from now.

Remove and install cooktop gas

devanti gas cooktop repair for one of the burners. That burner does not stay lit.

Need to cut space to larger size and replace with larger cooktop. Dispose old one.

Two jobs for electrician 1. Wire up cooktop- will need to supply junction box to go in cabinet. 2. Wire up pendant light in hallway. New light is supplied. To be completed before Wednesday.

Need to replace cooktop, oven and bathroom vanity in my investment property (remove, supply and install). Cooktop: 65.5 cm (l) x 51.5cm (w) Vanity: 90 cm (l) x 84cm(h).

install a new cooktop. already uninstall the old one, buckle up ready, basically just need plug the wire in.

remove old gas cooktop and install new

Need a certified plumber to swap out an old gas cooktop with a new one I bought. Same measurements, no electrical work needed and gas line already there. Hopefully just a simple swap as measurements of both cooktops are identical

Description: Need someone experienced to finish a kitchen job. Works required: • Supply & install 1 face panel for rangehood • Supply & install 1 box panel to cover ducting • Cut laminate benchtop and slot in electric cooktop Rangehood and bench already installed. Must have own tools and experience with laminate. Location: Bonnyrigg NSW Timing: ASAP Photos attached Please quote price and availability.

Replace old gas cooktop with new, same size. Dispose old gas cooktop.

Hi, I’m looking for a licensed gas fitter to safely disconnect and cap an existing gas cooktop. The cooktop is currently installed and access is clear. Please confirm whether removal and disposal of the existing cooktop is included. The apartment is located in Pyrmont, within a strata building, and parking is provided on site. Looking to have the work done during the week of 29/12 to 03/01 ideally Please let me know your availability and whether a compliance certificate is provided. Thanks!

Job is in Hurlstone Park. I’ve already bought an identical replacement 60cm Devanti ceramic cooktop. Bench cut-out is done, unit drops straight in, existing junction box is there. I just need the old one disconnected, new one wired in and tested. Can you give me a fixed price including GST for that, assuming no switchboard issues?

Hi, I need a licensed electrician to connect a new Devanti induction cooktop. The old cooktop has already been removed and the existing 240V single-phase supply cable (active/neutral/earth) is accessible in the bench cutout. The new cooktop has a standard terminal block with L1, L2, N, Earth and requires a single-phase install with L1/L2 bridged, as per the manufacturer’s diagram. Scope of work: • Hard-wire the new cooktop to the existing circuit • Bridge L1/L2 as per wiring diagram • Secure strain relief/clamp • Test operation + safety • Ensure compliance with AS/NZS 3000 Should be a straightforward job for someone experienced. Please confirm licence and availability. Thanks!

replacing a gas cooktop, its in place just beed to piping, one part needs new parts