Find experienced local carpenters in Rooty Hill

We have a stained 1.2m wide door with a large handle. At the moment the door is closed by locked and key. The problem is it does not have a deadbolt, so if someone forgets to actually lock it, it can just be pushed open unlike the old doors with deadbolt that once closed, though not locked cannot be pushed open from outside. So i just want a deadbolt put, it can be manual or the smart locks, the problem however, is that it has a big long handle, those who look at it said that the handle had to be removed to accommodate the lock, but that would mean leaving a hole where the handle will be removed. the bottom hole can be covered by the new lock mechanism (smart lock, i think) but the upper hole won't be, so it would look ugly. So i want someone who can: - put the deadbolt lock, can be manual if it does not have to remove anything. -or put a smart lock and if the long handle is to be removed, the hole will be patched and stained so as not to make the hole obvious or put something to cover the hole like a smaller handle to cover it and no need to re stain the door. Someone has to actually see it to recommend solutions

I need someone to put together y ardtopia Fremantle 3.6m x 3m Timber & Steel Gable Roof Gazebo it arrived in 4 boxes

The package is in the garage. So, help is needed to take it into the house. There are three steps of stairs into the house and it is going to be placed on the first floor so no more stair climbing is required after the 3 steps. Then, the wooden crate is to be uncrated and it would be great if you could help dispose it too. The wooden crate photo is attached as an example. The assembly is not required as it is sent being fully assembled. Only the circle part under the console needs to be attached. The dimensions are 200*40*42

Need to sand deck and restain the deck. we can purchase the stain. Unsure of SQM

Hey there, "GIVE YOUR BEST QUOTE" So I had this wall built up,as u can see the door in the middle. Now what I have planned is design the wall with timble cladding to give the wall and room a better look I am posting the current wall with the door and the height bottom to ceiling and width from one side to the other. So all I want is your quote and if you would like to get it done. I want a woody or Timber ( whatever you say it)cladding finish on the wall and door. Feel free to connect and discuss ideas if budget is feasible will get it straight done asap. Thanks. Hoping to get it done before 22nd September. Height: ceiling to floor 9 ft Width : wall to wall 9 ft Posting image and a 1 sample screenshot how I want

Renovation being conducted, walls have been removed and gaps where the walls were removed needs to be filled to match existing floor boards as close as possible. Also to be re-stained.

Need a joiner/carpenter for ongoing work. Duplexes, grannys, new homes, renos.

Cabinet making and installing

Need a good weld to fit the button stainless steel panel to the machine. Need it to be fully welded on, not spot weld. Also clean the weld.

Repair and Replace Rotten Sections of Wooden Deck at Blacktown International Sportspark Task Description: Hello! We’re looking for an experienced carpenter or handyman to repair parts of a wooden deck at Blacktown International Sportspark. The rotted wood sections will have to be removed, but we have a skip and will throw them out, but we need help with replacing the damaged sections and making sure the deck is safe and ready for use. One of the most affected sections is a set of steps that has to be replaced. Here’s what’s required: Wood Replacement: Measure, cut, and install new pressure-treated wood to replace the removed sections, ensuring a close fit with the existing deck. Wood Treatment: Apply a wood preservative to the new boards and surrounding areas to prevent future rot. Finishing Touches: Sand down any high spots and align the new boards with the existing deck for a smooth, safe surface. Final Check: Inspect the deck to ensure all repairs are sturdy and safe for public use. Requirements: Please bring your own tools and necessary materials, including pressure-treated wood and weather-resistant screws or nails. Previous experience with deck repair or carpentry is essential. The job must be done on-site at Blacktown International Sportspark. Timeline: This task must be completed no later than Thursday, November 14.

Make three pantry shelves

Paint one full new room (ceiling + walls ) and two external walls 3 windows frames to stain (one large and two very small) 3 new doors with frames to stain additional 2 doors only to stain in another area Doors and frames needs 3 coats Walls need 2 coats with one coat primer Work to start Saturday morning

Paint one full new room and two external walls 3 windows frames to stain (one large and two very small) 3 new doors with frames to stain additional 2 doors only to stain in another area Doors and frames needs 3 coats Walls need 2 coats

Qualified Carpenter Tradesman needed to help complete a contract this year. All materials are supplied and Subcontracting hours are flexible. If you are looking for a 3 day week or a 5 day week we are happy to work in with you and your other works but are offering a consistent supply of hours for the next 6 months. Budget is negotiable based on skill set and tool supply as it is broken down for hourly rates. - Due date: Flexible

Im looking for someone to make a bench top and cabinet on my laundry room

Need an experienced carpenter for on going work. Happy to sort $ in person - Due date: Flexible

Sand and Stain back deck. - Due date: Before Wednesday, 30 November 2022

Please see photos, tiny cabinet on sides of oven space is unusable, was thinking to cut the inside wall of the cabinet next to them and somehow make a single door that can open both spaces? Please offer ideas of what can be done. Thanks.

Assistance required for the week. Cut on site framing - carpenter needs you to cut and bring up wood, upon request. 7am starts. $30-35 per hour depending on experience. Located in Rooty Hill.

I need someone to go to a job site in Rooty hill for me tomorrow and finish off some bits and pieces. Fix off some end panels with keku fixings, cut some 100mm skiting, paint black and install. Must have own tools. Must be completed wed 25th.