Find experienced local carpenters in Perth Central

Airtasker Job: Convert Timber frame into Whelping Box – Perth CBD Budget: $100 labour only Looking for a handy person or carpenter to convert an existing timber frame into a safe, practical and attractive whelping box for my miniature dachshund, who is due to have her puppies on 1 November. The timber bed measures approximately 79 × 75 cm externally and 75 × 70 cm internally. Work required: * Install a solid, waterproof floor over the existing timber slats. * Build up the back and both side walls with plywood to approximately 30–35 cm above the finished floor. * Make a secure, removable sliding front door, preferably in two sections, so Della can enter and exit easily without jumping while newborn puppies remain safely contained. * Install three securely mounted PVC puppy safety rails (pig rails) along the back and both sides. * Reinforce the structure, smooth all edges and eliminate exposed screws or gaps where puppies could become trapped. * Keep the natural brown timber exterior sand all rough edges with a simple cream interior I have the timber bed, and washable puppy pads. Happy to purchase affordable materials from Bunnings or use suitable offcuts. I can provide photographs and an illustrated design. Location: Perth CBD apartment with parking onsite. Timing: Urgent — ideally completed today or tomorrow, before Della gives birth. Please advise your availability, experience and labour quote. Thank you!

Task: I need a replacement timber beam fabricated for a broken bed centre support beam. Dimensions: - Length: 2070mm - Height: 50mm (Must not exceed 50mm, as the bed slats sit directly on the beam) - Width: 25mm (Must not exceed 25mm, as it needs to slot into a metal bracket) Requirements: - A single solid piece of timber is preferred. - A built-up or laminated beam made from two is also acceptable, provided that: * Each piece runs continuously for the full 2070mm length and there are no end-to-end joins anywhere along the length * The pieces are properly glued and clamped along their full length so they act as one beam * The existing centre support leg is positioned halfway along the beam, ~1035mm from either end. It attaches with a screw through the side of the beam at the vertical midpoint, ~25mm from the top or bottom. Therefore, if the beam is built up by stacking timber to achieve the 50mm height, the glue line must not be positioned at the 25mm centreline. Unequal sections, such as 10mm + 40mm would be required * The finished beam meets the required dimensions above Material: KD hardwood or any suitably strong stable indoor material suitable for supporting a bed and mattress   Collection/Delivery: I can collect if location is within ~20 km of Perth CBD. Otherwise, delivery to Perth CBD will be required.   Refer to photos attached for visual detail. Please include in your offer: - The material you propose to use - Whether it will be one solid piece or laminated from multiple full-length pieces - Pick up or delivered - Total price, including material and fabrication

I have an assembled IKEA BESTÅ wall-mounted cabinet that needs to fit into the remaining space beside an existing row of BESTÅ cabinets. The wall appears to be slightly out of square. The top of the cabinet fits into the opening, but at the bottom it is only a few millimetres too tight to position and mount correctly. I need someone experienced with cabinetry/carpentry to: Check exactly where the cabinet is catching. Neatly remove/scribe approximately 2–3 mm (or only as much as required) from the wall-facing outer side/edge so the cabinet fits. Avoid damaging the visible finish or compromising the BESTÅ structure/mounting points. Ideally help position/hang the cabinet onto the existing IKEA BESTÅ suspension rail once modified. The cabinet is already assembled and the suspension rail is already installed. This should be a relatively small job for someone with the appropriate router/sander/cabinetry tools. Please bring your own tools. I would prefer someone who has experience modifying IKEA cabinetry or laminated/hollow-core furniture panels rather than simply cutting it with a hand saw. Photos attached showing the cabinet, the space it needs to fit into, and the gap at the opposite end of the existing cabinetry

Remove patio (wooden frame 8x10, transport to Boddington and Install.

Looking for a carpenter or handyman to: 1. Mount a 50 inches TV on the beams/studs inside gyprock wall. Need you to supply brackets 2. Quote on laundry cupboard renovations. It's a full laundry cabinet removal and installation. Sorry for some reason the app isn't letting me post photos. See photos in reply to Andrew's question below.

Light sand and stain 40sq mtrs of decking. Majority of decking under cover in good condition. Needs a restore.

Ive had to replace a 30yo oven. The new oven is smaller, I need a fill in shroud that fits the new oven and the old opening

looking for carpenters for a few weeks work in Morley $75 per hour

my car leaked oil in my carpark and im leaving the rental. i need help removing the pil. its in an apartment carpark without drainage and water

Needing a qualified carpenter to work on a regular casual basis or on ABN (whichever you prefer). Must be able to manage yourself and a labourer (if required) to do residential carpentry works and insurance repairs within the Perth Region. You would need your own vehicle and tools. Starting rate is $60p/h negotiable. I have a few jobs on hand and would be keen for a quick start. Reach out if interested.

Needing a qualified carpenter to work on a regular casual basis or on ABN (whichever you prefer). Must be able to manage yourself and a labourer (if required) to do residential carpentry works and insurance repairs within the Perth Region. You would need your own vehicle and tools. Starting rate is $60p/h negotiable. I have a few jobs on hand and would be keen for a quick start. Reach out if interested.

Need to install these two sliding doors in the designated opening. The doors may require trimming or minor size adjustments to achieve a proper fit. Ensure they slide smoothly, are aligned correctly, and all hardware is securely fitted and fully functional.

I need a new cabinet on my wall to match existing cabinetry. It needs to be Formica Snowdrift 0723. Height 730mm Depth 370mm Width 920mm Wondering what this would cost with or without installation.

Looking for a carpenter, ideally with a team, who would take on the build of a timber framed, cladded house.

Want a handheld gavel style door knocker made out of wood. Size is approximately 2 x 2 x 2 inches or 50 x 50mm.

Need to install stainless steel in a commercial kitchen in a restaurant . Everything will be provided

I am a cabinet maker and need professional joinery installer

This is for a carpentry work/ Handy man who is capable to do simple framing for ceiling (and minor staff for tiles.

2 book shelfs that need stilts or bases built to raise them to sit closer to roof and secured to wall. Seeking options and ideas on how safely do this. If fixing to wall is an available option that would be an advantage. Open to quotes for work and materials.

Hi, I am a cabinet maker and looking for competent installers. All items will be delivered to site ready for installation.