Find a professional balustrading contractor in NSW

repair balustrate , nails not holding them properly

Supply and install powder coated balustrades on a rock outdoor staircase. Replacing an old steel one

Looking for an experienced stainless steel fabricator/welder to assemble two balcony balustrades for a residential project in Mosman. I’m the builder and will supply the 316 stainless steel, dimensioned drawings and cutting list. I can cut the material ready for welding—happy to discuss your preferred preparation first. Scope: * Lower balcony: two panels approximately 3450 × 975mm and 1260 × 975mm. * Upper balcony: approximately 3700 × 195mm, with two short side returns. * Flat-bar construction with welded fixing pins and base plates, as detailed on the drawings. * Set out, jig, weld, dress visible joints and complete appropriate post-weld cleaning. Looking for straight panels, neat welds and a quality architectural finish. You’ll need your own welding equipment and experience with similar stainless balustrades. I’ll handle the coating and installation. Fabrication can be discussed for your workshop or on site. Please send examples of similar work, your availability and a labour price. Ideally completed before Christmas.

Glass balustrade for staircase L-shaped internal staircase (photos attached). We’d like frameless glass fitted on top of the existing walls, like the inspiration photo. Must be licensed, insured and NCC compliant. Please quote after a site measure. Location: St Ives

A number of steel balustrades at townhouse complex have surface rust. They need the rust to be removed, resealed and painted. Contractor will need to provide equipment and materials. Photos show the 3 affected balustrades.

Wire balustrade fencing around a newly poured concrete decking.

I have a small staircase and there are 2 spaces 96cm width 90cm height. I need a glass to be installed in the 2 spaces. It has wooden anchor. Currently there are metal wires installed, need to replace that with glasses. I have attached images of what i have and what I want.

The front porch needs 4 sections of balustrade replaced to match a newer section already replaced. I want to match is as close as possible but it doesn’t have to be exact. I would also like the old timber to be removed/ taken to tip.

Approx 2.5x2.5m bathroom ceiling to be cleaned, primed and painted. New stair balustrade to be stained and polyurethaned. All paint will be provided.

1.We require this space under the handrail to be filled for fall protection. Frosted glass pane is an option.The existing white timber post attached to the ceiling could be a structural, therefore it would remain. Alternatively replacing the metal guardrail with a white timber guard rail and white timber posts or slats for vertical screening/balustrade (option 2 on the AI generated image) 2. Remove the metal guardrail on the wall of the other staircase and replace with wooden white to match the downstairs guard rail. Price should include supply and install.

Increase existing balustrade height by approximately 400 mm. - Secure using suitable brackets, supports and mechanical fixings.

Im looking for a carpenter/handyman to relocate the existing outdoor timber staircase to the right-hand side of the courtyard and move the existing balustrades to the left-hand side. Ideally, I’d like to reuse the existing materials wherever possible. Scope of work: - Dismantle and relocate the existing staircase. - Reinstall the stairs on the right-hand side. - Relocate and reinstall the balustrades on the left. - Complete any necessary modifications, fixings and finishing. Please provide a quote, including labour and materials, and advise whether any structural modifications may be required. Must have experience with outdoor timber stairs and balustrades.

Increase existing balustrade height by approximately 400 mm

Supply and install approximately 8.2 linear meters of metal balustrade extension. Increase existing balustrade height by approximately 200 mm. Supply and install protective mesh/infill to the open sections, approximately 750 mm high

- Supply and install approximately 8.2 linear meters of aluminum balustrade extension. - Increase existing balustrade height by approximately 200 mm. - Supply and install protective mesh/infill to the nominated open sections, approximately 750 mm high.

Paint colourbond balustrade on upstairs deck. Paint provided. Labour only.

I need a timber stair balustrade removed carefully. The job includes: * Remove the entire timber balustrade (vertical posts and top rail) shown in the photos. * Remove fixings (screws/bolts/nails) where possible. * Minimise damage to the existing timber capping and surrounding walls. * Stack all removed timber neatly (or dispose of it if agreed). The balustrade is approximately 2–2.5 metres long. Important * I believe this is not structural, but please inspect before commencing. * If you believe it provides structural support, stop work and discuss before proceeding. * Care is more important than speed. * Please bring your own tools (multi-tool, pry bars, drill/impact driver, etc.). Preferred experience * Carpenter * Handyman experienced with timber balustrades * Cabinet maker also suitable Questions for Taskers 1. Have you removed similar balustrades before? 2. Will you minimise damage to the timber capping? 3. Can you dispose of the timber if required? 4. Approximately how long do you expect the job to take?

Stair balustrade to be painted (light sand, primer, gloss white x 2 coates). Perspex will be removed

Install a frameless standoff glass balustrade using materials I supply on site. Balustrade is located more than 5m above ground level, so it must be installed and certified to AS 1288 / AS/NZS 1170 by a suitably qualified and licensed tradesperson. Materials on hand: • 15mm frameless standoff glass panels: 850W × 1280H ×6, and 750W × 1280H ×3 • Summit 30×21mm Nanorail Deluxe handrail 5800mm (satin) ×2 • Summit Nanorail Deluxe rigid glazing rubber 2900mm ×3 • Summit 30×21mm Nanorail Deluxe wall plate extended (satin) ×6 • Summit 30×21mm Nanorail Deluxe 90° joiner (satin) ×1 • Glass standoffs 38×25mm (satin, SS2205) ×48 Note: fixing rods are NOT supplied — please include any missing items in your quote. Scope: • Labour-only install of the above into the existing structure, glass 15mm toughened with Nanorail top rail fixed into structure • Confirm supplied standoffs and fixing details suit 15mm panels for a balustrade above 5m per AS 1288 before commencing • Flag anything missing or any recommended change to the fixing approach prior to install • Provide a Certificate of Compliance on completion from a licensed/qualified trade, expressly noting the balustrade is more than 5m above ground Requirements: • Appropriate trade licence and insurance — please state licence number • Quote labour only; advise availability and lead time Site: inner Sydney. Please confirm you can certify to AS 1288 at this height before quoting.

Front of House Balustrade and back balcony Balustrade - total of Approx. 18 - 20m. Simple straight line balustrade (to be painted black). Paint will be supplied - need someone to prepare, prime and paint before the 1st May 2026 (latest 5th May). Any questions, just ask. Would love the help. Thank you!