Find a reliable appliance technician in Ryde

LG washer + dryer needs repair status code OE Water not draining properly

Built-in Bosch Serie 4 dishwasher is showing error code Err 15 / E15 and won’t run. From what I understand this usually means the leak-protection (Aquastop) system has picked up water in the base and shut things down — could be a valve or seal issue, but I could be wrong, so keen for someone with actual appliance repair experience to have a proper look and diagnose it. Looking for someone to: • Diagnose what’s actually going on and quote for the fix • Sort out any parts needed (happy to cover cost, just quote separately) • Get it running a normal cycle again without the fault coming back It’s built into the cabinetry, so you’ll need to be comfortable pulling it out and putting it back in cleanly

Could you please provide a quote on repairing a wall mounted Fisher & Paykel Aerologic 5kg Dryer? Issue: when the dryer is fully loaded, the spinning slows down a lot. With a few pieces of clothing, it returns to normal.

The dishwasher is not leveled well，1 side is wide and other side is narrow, and not at the same level with other cabinet

Hi I would like someone to come and replace my washing machine door seal Model no haier HWM75-B12266 I will need the seal supplied too.

1. Remove old dishwasher 2. Install new dishwasher 3. Fix kitchen sink pipe leak

Can still smell gas near an outdoor gas outlet/valve. Valve looks off but smell persists. Need a licensed gas fitter to check for a leak and fix/replace if needed.

Job Details * Remove existing 60cm wall-mounted rangehood and dispose of it. * Install new 60cm wall-mounted rangehood (filter type, no external ducting required). * Repair two downlights (optional).

Help fix my breville coffee machine The grinder is stuck and i can't twist or remove it

We are having some modifications done in our Kitchen to install a small cutlery drawer above our microwave oven (as a separate Airtasker Task). However, for that task to go ahead, we need to ensure the Power Point to our Microwave Oven does not clash with the new drawer to be installed. The current Power Point is in the top left hand corner of the enclosure, we require it to be moved downwards by about 100 to 150mm. I think the Power Outlet is surface mounted to the back of the enclosure, and from what I can tell, the power cable comes into it from the cabinet wall on the left hand side, which is the sink enclosure.

Hello, We are looking to have a small utensil drawer installed in our kitchen in Meadowbank (Ryde area). The drawer would sit directly above our small microwave oven, inside the current microwave enclosure. The new drawer cutlery drawer would be done in the style to match the existing drawers. As part of the job, the facia around the microwave oven enclosure would need to be removed as it clashes. Additionally, the power point inside the microwave enclosure, may need to be moved downwards by about 150mm. I have supplied photos, and a concept sketch of the proposed cutlery drawer. We would like to have someone come out and visit us on site, and measure and quote for the design. We are looking to have the job done in the next few months. We have in mind a budget of somewhere in the order of $1, 000 to $1,500 for this task. Regards, John Drake.

Hi there, I need a licensed NSW gas fitter to rectify a gas installation defect identified by Jemena on my property in Eastwood. The defect noted on the certificate is: "Earth stake & weep holes in exclusion zone". Scope of work: Relocate/extend the gas regulator vent line or pipework to ensure it is clear of the electrical earth stake and building weep holes (per AS/NZS 5601.1 standards). Perform a pressure/leak test upon completion. Issue a formal Certificate of Compliance and a Leak Test Certificate as required by Jemena. Please refer to the attached photo of the Jemena Non-Compliance notice for exact details. Must be fully licensed and insured in NSW. Please provide your license number when offering. Flexible with timing but needs to be completed within the next few days. Thanks!

Need someone to fix my washing machine. Can’t open the bottom to clean it, I’ve tired pliers. It still washes fine

washing machine is leakin

Dishwasher isn’t working and is displaying a F30 error code. Brand: Haier Model: HDW13V1S1 The property is a house and the dishwasher is located on the ground floor.

Rangehood Replacement – Supply and Install, size on the pictures Remove and replace the existing standard kitchen rangehood. Supply a new standard rangehood suitable for the existing installation. Installation to include all labour, fittings, and materials required for a complete replacement. Ensure the new rangehood is fully operational upon completion. The existing rangehood may be left on the property after removal.

Miele dishwasher F11 error — approx. 2.5 years old Description: Hi, I’m looking for someone experienced with Miele dishwashers to inspect and repair my dishwasher. It is quite new, around 2.5 years old. Out of warranty, The dishwasher can still run and wash normally, but it sometimes shows an F11 error.

Needing someone to connect my washing machine to the outdoor laundry vanity. Was not connected previously and will show in photos

Need to fix tap and run washing machine hose under neath the sink

Please help install home battery cover like the pics showing, covers bought already.