Find a reliable appliance technician in Ryde

Install and seal external vent, penetrate internal brick wall, pipe and plumb to existing 125mm rangehood. External hole was done as part of another AC install but internal wall and piping to rangehood was out of scope so looking for someone to help complete this. Only have external vent and hose as shown in picture. No rangehood installation required. Will require qualification/licensed/insurance Ideally sometime this week Let me know if any more information is required thanks!

I just bought a new washing machine and it needs a hoseclamp connected, I also have a new fridge that needs the water connected to the back of the fridge. Probably only 5-10 minutes of work but I would prefer someone do it who knows how to do it properly. Also need someone to buy the hoseclamp I don’t have one

Help me fix my fridge please Freezer is working but fridge is not Might need to replace something?

Looking for someone experienced to install a new Bosch Series 6 60cm fully integrated dishwasher. Job includes: * Disconnect and uninstall the existing dishwasher * Install and connect the new Bosch Series 6 fully integrated dishwasher * Reuse and fit the existing cabinet/front door panel to the new dishwasher * Ensure the dishwasher is correctly levelled and the front panel is aligned with the surrounding cabinetry * Check all water and drainage connections * Test the dishwasher after installation to make sure everything is working correctly and there are no leaks Existing plumbing and power are already in place.

Replace range hood from old to new

Require a new gas cooktop installed only. Attachments and cooktop on site. Just need it to be connected by a qualified person.

Change to a new filter could not clean

We have just made room for a dishwasher in our kitchen and are now needing a plumber to install it. The hoses are feeding through the corner cabinet but are not long enough to reach the sink. A hole will need to be cut in the dividing cabinet to reach the sink.

Fix clogged dishwasher in apartment

Issue with power, it goes on and off for a while. Now it doesn’t turn on at all.

F138 error on washing machine, have done us trouble shooting

I have a new Beko BRH70UX 70 cm undermount rangehood ready to install. Looking for an experienced rangehood installer/cabinetmaker to remove the existing rangehood and install the new unit. Scope of work: * Remove existing rangehood and dispose of old unit. * Install new Beko BRH70UX 70 cm undermount rangehood. * Existing kitchen has a gas cooktop, so installation needs to comply with applicable Australian clearance requirements and Beko installation requirements. * Existing cabinetry/shelf will likely need to be modified/raised to position the new rangehood correctly. * New Beko requires 150 mm duct connection (120 mm adapter also supplied). * Existing ducting is only 100 mm, so this needs to be replaced. * Ducting needs to be rerouted to the other side of the cabinet/duct path. * Please supply/install appropriate 150 mm ducting, joins, elbows, clamps and external connection as required. * Keep duct run as short/straight as reasonably possible. * Modify cabinetry neatly and securely around the new rangehood. * Connect to existing power point * Test rangehood/extraction after installation. * Clean up and remove rubbish. Rangehood: Beko BRH70UX Width: 700 mm Depth: 296 mm Height: 254 mm Cabinet cut-out: 665 × 265 mm Duct: 150 mm preferred Photos of the existing installation and new rangehood are attached. Please quote for labour + materials and clearly identify any additional costs. Looking for someone experienced with rangehood installation, ducting and kitchen cabinetry, rather than a basic appliance installer. Budget: $700–900 depending on the amount of cabinetry and ducting work required.

Replace door seal. on samsung washing machine. I have the seal already

Washing machine filter needs unblocking

Faucet/tap that provides water to a washing machine is leaking.

Please quote your hourly rate. We are moving into a new home and need someone who can handle three appliance installations end to end: Install a Bosch freestanding dishwasher Supply connection and install a freestanding gas cooker Install a washing machine The kitchen already has a freestanding gas cooker, so that one is a straight replacement. The dishwasher and washing machine are new installs, so the plumbing needs to be run from scratch. This is a rental property. Both new installations need to be done neatly and reliably so they hold up for at least two years, and so a plumber can remove the dishwasher and washing machine cleanly at the end of the tenancy without damage to the property. We already own the washing machine and dishwasher. We are still purchasing the freestanding gas. Happy for you to charge us for additional pipes etc needed, or if you give us the list, we can buy it from Bunnings.

LG front-load washing machine needs urgent repair. The machine was working normally yesterday but now shows DE2 error and the door keeps clicking but won’t lock, so the washing cycle won’t start. Looking for someone experienced with LG washing machines to diagnose and fix the issue. Available ASAP.

Help fix my breville coffee machine The grinder is stuck and i can't twist or remove it

We are having some modifications done in our Kitchen to install a small cutlery drawer above our microwave oven (as a separate Airtasker Task). However, for that task to go ahead, we need to ensure the Power Point to our Microwave Oven does not clash with the new drawer to be installed. The current Power Point is in the top left hand corner of the enclosure, we require it to be moved downwards by about 100 to 150mm. I think the Power Outlet is surface mounted to the back of the enclosure, and from what I can tell, the power cable comes into it from the cabinet wall on the left hand side, which is the sink enclosure.

Hello, We are looking to have a small utensil drawer installed in our kitchen in Meadowbank (Ryde area). The drawer would sit directly above our small microwave oven, inside the current microwave enclosure. The new drawer cutlery drawer would be done in the style to match the existing drawers. As part of the job, the facia around the microwave oven enclosure would need to be removed as it clashes. Additionally, the power point inside the microwave enclosure, may need to be moved downwards by about 150mm. I have supplied photos, and a concept sketch of the proposed cutlery drawer. We would like to have someone come out and visit us on site, and measure and quote for the design. We are looking to have the job done in the next few months. We have in mind a budget of somewhere in the order of $1, 000 to $1,500 for this task. Regards, John Drake.