Find a reliable appliance technician in Outer West Sydney

Hey my hair straightener just died on me it’s not even two years old. It’s a wise plate MUk. I’m wondering if someone can fix.

Looking for aan electricianto install a new Westinghouse WVE6526DD built-in electric oven in my home in Erskine Park, NSW. Scope of work: - Inspect existing connection point. - Verify cable size and suitability for the new oven load (5.6 kW / approx. 23.4 A). - Hardwire and commission the new Westinghouse WVE6526DD oven. - Inspect the electrical circuit and switchboard. - Replace the existing oven circuit breaker with an appropriately rated breaker (30A or 32A/35A as required and compliant with AS/NZS standards). - Test oven operation and provide electrical safety testing on completion. - Advise if any additional wiring upgrades are required before installation. Requirements: - NSW Licensed Electrician. - Please include the cost of labour and specify whether the circuit breaker/ wiring for the new oven is included in your quote. Additional Information: - Oven is already on site. - Existing wiring needs to be checked before connection. - Photos of the switchboard and oven location can be provided upon request. Location: Erskine Park, NSW Please quote your total price and earliest availability.

One of the gas burner shuts down when on low flame. Need help fixing it.

Turns on Inclines and declines Doesn't run. No noise to indicate it wants to run.

I’m looking for an experienced technician to diagnose and repair my Breville Oracle espresso machine. Symptoms: * The steam wand works normally while steaming milk. * Once the milk reaches temperature, the machine starts making a buzzing noise, as though a valve isn’t closing properly. * When I lift the steam wand, the buzzing/purging stops and everything seems normal. * If I leave the machine switched on, it eventually trips the electrical circuit. * If I switch it on, make two or three coffees and turn it off, it works fine. I’ve been told it may need the steam wand/steam valve O-rings replaced, but I’d like someone experienced to diagnose the actual cause rather than just replace parts unnecessarily. What I’m after: * Diagnosis and repair of the fault. * Replacement of O-rings or valves if required. * A quote for parts and labour before proceeding. I’m located in South Penrith, NSW.

Need replacement of Fisher and Paykel (DW60FC1X1) dishwasher drain hose.

we have an old gas heater which we would like to get disconnected so that we can put furniture in that corner.

Repair draw hafale style soft close face came off

Need to remove electrical connection of existing oven hardwired to MSB. Need to provide new socket for dishwasher

Old machine removal replacement with 10 kilo Chiq machine

Looking for a licensed electrician to replace an old electric oven with a new oven that I will supply. Photos of the oven I want to get attached The tenant has noticed a burning smell and said the outside of the oven is becoming unusually hot, so I also need the wiring, connection and circuit checked to make sure everything is safe. Location: St Clair, NSW Required: As soon as possible Please send me your price and a few available appointment times so I can confirm access with the tenant.

We are having new kitchen bench tops installed at noon today and forgot to arrange to have an electrician disconnect the cooktop. Urgently need someone to attend at 11.45-12 to disconnect it.

Need a new kitchen tap bought and installed so we can use Bench top DW and the taps

I have an Amantii TRD-30 electric fireplace that is completely dead with no display or lights. I need someone who can diagnose internal power supply, fuse, thermal cut-off or control board faults and then fix it if its an easy fix. The heater was purchased as brand new faulty from a shop. Located in St Clair.

I need someone experienced with washing machine repairs to replace the door seal/gasket on my Hisense front loader (model HWFY7514). I've already purchased the correct replacement seal — it's the genuine HWFY7514 seal with the Pure Jet spray hole, so no need to source parts. The job: • Remove the old damaged door seal (mould-affected, needs replacing) • Fit the new seal, making sure the Pure Jet nozzle aligns correctly with the spray hole • Refit the retaining clamp/ring securely • Run a quick test cycle to confirm no leaks and the door seals properly Must have prior experience fitting door seals on front loader washing machines — please mention relevant experience in your offer. I'll have the machine accessible and unplugged, with the new seal and manual on hand. Should be a straightforward job for someone who's done this before — happy to discuss timing. Budget: $60–80 (labour only, part already supplied)

Part of the silicon has ripped which is causing some of the water in the washing machine to leak out when it’s running. We would like the silicon replaced or repaired if possible.

Both my GHD Platinum+ and GHD Max straighteners are flashing red and no longer heat up. The warranties have expired. Could you please advise whether these models are repairable and provide an estimate for diagnosis or repair?

Replace new dishwasher with old dishwasher. Located in Llandilo. Please only accept this task if your confident or have done this before

Ride on lawn mower not turning over need someone with auto electrician experience to diagnose issue. Thnks

Installing a dishwasher to an existing plumbing line location: Cnr Doonmore St & High Street date: 8/5/2026 time: 2PM