Hire a trusted gas stove repair and installation service in Inner West Sydney

All my gas stoves are working but the output of gas looks very low and takes long time to cook using multiple stoves.

Licenced gas fitter to disconnect existing cooktop and install new cooktop

Hi 👋 I’m looking for a gas technician / appliance repairer to fix one burner on my gas cooktop. Issue details: • The bottom left burner does not stay on • When pressing the knob, gas ignites and flame appears • As soon as I release the knob, the flame goes out • Other burners are working normally • The knob does turn and spark, it just won’t stay lit From what I understand, it could be a faulty thermocouple or ignition issue, but I’m open to inspection. Cooktop details: • Built-in gas cooktop (see photo) • Brand/model can be provided if needed • Apartment location What I need: • Diagnose the issue • Repair or replace the faulty part if possible • Ensure everything is safe and compliant Please let me know: • Your licence (gas fitting) • Estimated cost (call-out + repair) • Availability Thanks!

Job: Remove old gas cooktop + install new 600mm Fisher & Paykel (Burwood) Location: Burwood, NSW New cooktop supplied: Fisher & Paykel CI604CTB1 (600mm) Timing: Flexible — please advise your availability. What I need • Disconnect and remove existing gas cooktop • Install new 600mm cooktop into existing benchtop cut-out • Connect and commission safely: • Gas connection (leak test + burner/ignition test), and/or • Cap/secure gas line if new unit is not gas (if applicable) • Optional: dispose of old cooktop • Provide compliance certificate/documentation if required (NSW) Please include in your quote • Total cost (labour + call-out + any fittings) • Whether disposal is included • Licence/insurance details I can send photos of the current setup and under-bench connection.

Remove old 4 burner gas cooktop fit new Devanti 4 burner cooktop all fittings supplied

Old Gastop and new new gastop replacement work. Gas entrance is opposite, so a connection is required And Plug oven should I call electrical devices?

Replace gas cooktop with new, installation only. Licence gas fitter.

Gas stove igniters keep sparking when burner isn’t on. Will need an inspection first, and can cover cost of required repair.

Licensed Plumber Required All products have been purchased – installation only required • Remove existing sinks and install 2 × new vanity/sink units • Install 2 × shower rails • Replace kitchen tap • Remove existing and install new gas stove • Ensure all plumbing and gas connections are compliant and tested

2* Install privacy lock and check gas stove

I am looking to repair my Smeg gas cooktop (Model: CIR93AXS3). The Problem - The issue is a delayed ignition on all burners. When I press and turn any knob, there is no spark or clicking sound for a couple of seconds, and then it finally lights. Requested Services & Parts - 1. Diagnosis: Confirm the cause of the delayed sparking across all burners. 2. Replace the Spark Module (Ignition Generator): This is the most likely solution to the main ignition delay problem. 3. Replace Two Loose Ignitors: Two of the ignitors (the spark plugs next to the burners) are physically loose and need to be secured or replaced. 4. Replace one Ultra-Rapid Burner Head (Old Style): One of the burner heads is cracked. I would like it replaced if you can source the spare part. Please quote me the labour and parts

The stove was working fine. It was cleaning the dirt, and then the light is not able to get on. The Gas is fine that can smell it, and having the “ da da “ sound, but not able to light on.

Hi I have a gas cooktop (5 burners 75cm), that i would like to replace with an induction cooktop. I have a single phase supply , in a house , remove and cap gas supply, Ashfield. Leave safe and compliant for future inspection. Provide compliance paperwork. Also handle all electrical work. hard-wire the unit, and install an isolator if required. Verify clearances and add a heat deflector if needed. Provide compliance certificate. I can provide the induction cooktop. 15 meters to electrical switchboard. Roof access( well maintained roof space with plenty of lighting) Quote needed

Want to replqce gas cooktop with induction

Plug gas connection on new kitchen stove

1. The existing bench cut out is 585mm x 500mm, the new cooktop base is 595mm x 455mm. 2. The existing gas pipe needs to be rerouted under the cooktop.

Gas already on the property. Need to connect gas pipe to the kitchen area for new cooktop and oven. Installation of cooktop and oven required.

My ignitors on my gas stove is not working and one of the knobs is not clicking and staying down.

To help fix the igniter on my Miele gas cooktop. The gas burners are working fine when lit manually, but the electric ignition system is not sparking (no clicking sound either). I’ve already: Checked the gas supply ✔️ Cleaned the burners and igniters ✔️ Confirmed power supply is working ✔️ Looks like the issue might be with the ignition switch, spark module, or igniter wiring. Would appreciate someone who has experience with Miele appliances and can bring the right tools to inspect and repair it

Remove old gas cooktop, replace with a new gas cooktop including supply of the cooktop