Find professional window and door services in Canberra

I need to get my garage roller shutter motorised

The laundry room door has partially come off the wall, and the rollers above the door have come out of the track too. I need to re-secure it. I can provide power tools, nails, hammer.

1970 Toyota corona rt80 driver side door has sagged. There is a substantial amount of play in the upper and lower hinge. The door rubs on the front guard when opening and closing the door. I want someone who can fix both the hinges and align the door to ensure it doesn't rub.

Had the Holman Misting System installed at our old house to cool the verandah and house down. https://www.bunnings.com.au/holman-7m-misting-kit-with-swaplock-fittings_p0544771 Awaiting a surgery and unable to install myself now at our new place. Likely needs to be put up with zip ties or clamps of some sort along the aluminium slats as an attempt to install before my injury on the facade (shown with red stars in image) of the townhouse was unsuccessful as it’s too hard for the hose clamp nails. I’m surprised by some of the one star reviews of the Holman System. I’m not adverse to purchasing the Hoselink System if you have it yourself and recommend. https://www.hoselink.com.au/products/15m-misting-kit-with-directional-heads?variant=19426026750048

There is a non bearing wall that needs a cut out and a door installed. Please see the attached photos of the wall (it being built, and it finished).

Need to install bunning’s 2040 x 1000 mm flyscreen door installing outside or inside the existing door

Need someone to: 1. Reattach 2 hinges to laundry door. 2. Tighten screws on 3rd hinge still attached. Not sure if missing screws or other fixtures to complete this.

3 doors out of their tracks 3 door handles loose , needs tightening

2 small tasks 1. Reattach screw to top of outdoor shade umbrella 2. Install new door handle. New parts already purchased

The sliding door is ajar and does not close properly.

Hi, I need someone to repair my sliding screen door. The mesh has come loose and torn along the side and bottom, and the frame no longer holds the mesh in place properly. It’s sagging, pulling out of the track, and won’t close or slide smoothly anymore. From the photos, you can see: • The mesh is frayed and detached on one full vertical side • The bottom section has come completely out of the frame • The sliding track alignment seems off • The frame may need re-tensioning or re-meshing I’m looking for someone who can: • Re-mesh the screen OR repair and re-fit the existing one if possible • Ensure it slides properly again • Do the job as cheaply as possible while still making it functional Please send me a quote after checking the photos. Happy to work around your availability. Thanks.

we’ve had new windows installed but they are leaking!! Architraves are not sitting right up against the brick. We need someone who has confidence using a silicon gun and can apply silicon to the gap in between the architrave and the brick wall. It needs to be fully sealed and it needs to look professional. There are four windows. Three windows are 1000 x 2000. The fourth window is 4000 x 2000. The biggest issue is 2 of the windows have beds in front of them and so the mattresses and the bed frames will need to be taken out of the rooms first. Then put back into the rooms. No time wasters. I need someone who has experience in this kind of work. That close-up of the gap between the architrave and the brick is showing the smallest gap. There are much bigger gaps - up to 3mm. I need the exterior checked as well.

Purchase hinge and all supplies, install kitchen door and test functionality. Quote to include labour, travel, any supplies required, provision of any tools required and a final test to ensure it closes properly. Home owner to provide door but no hinges or screws.

I need someone to drill into my brick wall and install my ring doorbell. (It's battery, not wired). I have drilled 1 hole but unable to do the rest 3. Small and easy job for someone experienced hopefully

1. Remove sliding glass door replace or service rollers, clean sliding areas and make good. 2. Replace mesh on sliding mesh door. Replace in sliders and check functionality. 3. Ensure all working properly before leaving. 4. Glass door is heavy double glaze so will require two men to lift or experience doing so. Advice if you need help from home owner. 5. One Glass sliding door and sliding mesh door to be serviced. 6. Supply all materials and cleaning supplies.

Replace the flyscreen mesh on one sliding door and one window. Flexible with time but the earlier the better.

I have 3 fixes to be done 1. Fix cabinet door, new a new hinge and install it 2. Fix broken drawer 3. Flooring need to be fixed

My dog has chewed the window frame (2x areas) need this fixed up as if it hasn’t happened. Sanded, bogged and repainted at a guess?

My automatic garage door not opens fully up and not close properly. When pressing the close button on the remote, the door starts rolling down but then the roller wheel misaligns when coming down and sit outside the track. It looks like the issue is coming from the left corner roller area, which may be due to misaligned. The corner panel also appears slightly misshaped, likely causing the door to bind. Please see the attached photo for reference. Work required: Inspect the corner roller and alignment. Adjust or replace the roller if necessary. Check and realign the corner panel. Ensure smooth and safe operation of the door after repair.

Door is off hinges so needs to be realigned and a lock needs to be put back on the door. Have the lock but missing the screws so a handyman who can bring screws with them is preferred