Find a professional tiler in NSW

Installation of tiling on laundry floor and tiled skirting. You need to install the tiling with adhesive glue, supply a new white floor waste. Make sure the tiling matches the kitchen level. I will supply the angle and the tiles. Floor area = 1.475m x 2.08m = 3sq.m Skirting length = 3.5m I have bought the tiling already. 300mmx300mm.

Need to do floor tile 60/60 on new floor approximately 50 square metres It’s shop floor & no room. Only 1 area where need tiles. I need compliance. As it’s commercial site . I Need your license & insurance.

I have existing bifold doors on my ground floor alfresco that need to be removed and reinstalled on the opposite (left) side wall. The exposed floor area will also need tiling to match and raise the existing floor level

Bathroom floor tiling will be required due to changing drainage system. Bathroom size appx 6 sqm. Single storey fibro dwelling with subfloor. Scope of work- - Take off all fittings and put back after floor done such as shower Screen, Vanity and toilet sit . - Demolition of floor and rubbish removal (take with you) - Redo Bathroom floor including water proofing. Screeding grouting etc. *Tiles will be provided. Only Flooring, walls will remain same.

Looking for a quote to tile over existing floor tiles (2.5sqm) and remove and replace 5 wall tiles. More detail shown in the attached images. Looking for an experienced tiler to complete two jobs in my bathroom: Wall tile repair – Remove and replace a few damaged wall tiles without disturbing the waterproof membrane underneath Floor tile overlay – Tile over the existing floor tiles with new tiles (https://tilecloud.com.au/products/seaforth-travertine-look-beige-matt-1) Scope of work - Carefully remove tiles for towel rail, roll holder, soap holder. - Inspect area to ensure waterproofing is intact - Clean and prep the substrate - Install replacement tiles to match existing layout - Grout and finish Floor tiles (tiling over existing tiles) - Prep existing floor tiles for bonding (clean, degrease, lightly sand/scuff glazed surface) - Apply suitable primer/bonding agent for tile-on-tile adhesion - Lay new floor tiles using flexible tile adhesive rated for tile-over-tile - Grout and seal as needed - Ensure transitions to door threshold and fixtures are neat All tiles provided but if you are able to source an exact colour match for the wall tiles that is a bonus!

Floor tiling in house as attached - areas highlighted - the property is currently being renovated. Approx 91 square metres for the main floor area + toilet, Bathroom & Laundry. We will supply the tiles, either a timber look tile, or a 600x600 porcelain tile. Depending on the cost we may consider some wall tiles in the bathroom area as well. Thanks

27sqm of floor tiling to be done. I have tiles and glue already. Must be tiler

The need more space on bathroom. So uproot the bathtub and complete the by fixing floor tiles and wall tiles. You buy tiles and whatever is required

It's a three-level house with 5 bedrooms and 7 bathrooms. We need to do the sand levelling, tiles and marble installation for all the bathrooms, corridors and living room areas. The project needs to start in July or August.

Tiling laundry and toilet floor over existing floor, skirt tiles to be done also I will supply tiles and pull off existing skirting tiles

Floor Tiling work. Replace nine 60x60cm tiles after some plumbing work. Great if you can get the tiles. Examples of tiles in photo attached. These tiles will be ripped out for plumbing work. The floor will be concreted again for the new tiles.

Floor tiles in shop front

Pull up carpet and tile area Approx 10sqm Already have tiles 900 x 450

Needing floor tiling installation done for small 11 sqm area see images.

Need a 3.2m2 floor + 1 row of wall area tiled. Today preferably can also be tomorrow. It’s been waterproofed and glue will be provided you will just need to cut and lay.

Tiling required for laundry area. Dimensions are approximately 1800*2500mm. Should be sloped towards the door so water can run outside. Tiles will be supplied.

Ceramic tile over existing tiles. 7m2 total area. Waterproof to shower tile floor only prior to laying new tiles.

We need an experienced tiler to lay tiles over existing tiles for our bathroom floor. We have had a tiler our previously who has confirmed this is doable. (Note: No full bathroom waterproofing required beyond localised drain integration unless otherwise agreed. We will remove the toilet.) Location: Bathroom Area: Approx. 3 m² floor area Existing condition: Existing tiled floor to remain; new tiles to be laid over 1. Preparation     •    Inspect existing tiled floor for soundness and suitability for tile-over-tile installation     •    Clean, degrease and mechanically prepare surface as required (grind/scarify if necessary)     •    Apply appropriate bonding primer suitable for tile-over-tile applications 2. Drain Modification & Installation     •    Remove existing floor waste grates     •    Modify existing PVC floor waste pipe(s) as required to suit new finished floor level     •    Supply and install new compatible floor waste body / puddle flange and adjustable riser (or equivalent compliant system)     •    Install new Elson 80 mm square brass grates, set flush with finished tile level     •    Ensure falls are maintained toward drains 3. Tiling Works     •    Supply and install suitable flexible tile adhesive     •    Lay new heritage-style mesh-mounted tiles over existing tiles (approx. 3 m²) - we will supply tiles     •    Cut tiles neatly around floor wastes and perimeter     •    Ensure correct alignment, spacing, and falls to drains 4. Grouting & Finishing     •    Grout floor tiles with suitable grout (colour to be confirmed)     •    Silicone seal perimeter junctions where floor meets walls / fixtures     •    Clean down and remove all debris from site 5. General     •    Builder/tiler to supply all labour and standard consumables     •    Owner to supply tiles and grates (unless otherwise agreed)     •    Work to be completed to a professional standard with tidy workmanship

Tiling 2 bedroom areas app 3 x 4 metres and 2 x 2 metres. other jobs TBA. Looking for quotes for hourly, daily or per metre squared rates for tilers.

We need 44 sum metre of floor tiles laid. They are 1200x600 tiles. Also need a splash back done. It’s roughly 7mx 60cm high 20x20 square tiles

Need someone to cut porcelain tile for me

Hang porcelain wall art, a clock and some pictures in double brick wall. Total of 8 drilled holes required for 6 items - 2 big ones need 2 holes each .

Have spare tiles. Some need cutting. Bottom step Needs to be rebuilt

Several chips on bench too and shower niche joint lines need repairing

Need a crack in the sink repaired

1.5cm chip on a tile. Need it fixed by a handyman as requested by the owner of the place.

Repair of Cracked Porcelain Sink- See Photo

Would like a qoute for porcelain stone splashback and porcelain stone benchtop . We like wood backing underneath for durability. We found porcelain stone in factory we just need you to buy for us and install in our kitchen . Cabinets in kitchen are made and ready .. Nexted stage is porcelain stone instaltion . Need done asap.

Need a quote to hang a mirror (900 x 600mm) in a bathroom that has a porcelain tiled wall please. Here is the link to the mirror: https://www.poseidonbk.com.au/products/poseidon/mirror-2/aura-mirror-2/aura-framed-mirror/oliva-arch-yellow-gold-frame-mirror-kar6090f-bg/

I need a single straight cut on a 20mm thick porcelain paver. The Details: Material: 20mm Italian/Outdoor Porcelain (Damia brand). Task: One straight cut across a 600mm paver. Context: This is for a pedestal system next to a door, so the edge needs to be clean and chip-free. Requirement: You must have a wet saw or an angle grinder with a specific porcelain diamond blade. Location: Erskineville. Easy access in the front yard/driveway. I only have one spare paver, so I need someone confident they can make the cut without shattering it. Flexible on timing—happy for you to swing by if you're working nearby.

Need 4 Mirrors Mounted on Tiled Bathroom Walls Looking for an experienced handyman to mount 4 mirrors securely onto tiled bathroom walls. Details: - 4x mirrors to be installed in bathroom - Walls are fully tiled - Drilling into tiles required (must avoid cracking tiles) - Need clean, level alignment and professional finish Requirements: - Must have experience drilling into tiles - Must bring correct drill bits (tile/glass bits) and fixings - Prefer someone who has done similar bathroom installs Looking for a neat job with no tile damage.

New Bathroom mirror needs installing on porcelain tiles

I've tried Lithofin Intensive cleaner and Stain stop sealer, some places it's worked, others not so. Did not use mechanical scrubber. Tiles are Lappato semi polished ONLY tile professionals need apply, not a DIY or handyman - please dont waste my time or yours. thank you

! I’m looking for an experienced tiler to tile a small bathroom wall section. Wall size: approx. 73cm wide x 227cm high (Photos attached) Tiles: Supplied (same style as shown in reference photo) Grout: Supplied I’d like the tiles laid in the same staggered / random pattern as the sample. ⸻ What needs doing • Prepare wall surface (ensure clean, level, ready for tiling) • Tile the wall section neatly • Cut tiles as needed around edges/fixtures • Grout and finish cleanly • Silicone/seal edges where required • Leave area tidy afterwards ⸻ Notes • This is a small wall, but I want a high-quality finish (straight lines, even spacing, clean cuts). • Please bring your own tools. • I supply tiles + grout

Slate tile removal (optional): please quote separately Supply tiles (Optional): please quote separately Scope of Works 1️⃣ Optional – Existing Slate Tile Removal (separate price) Remove existing slate tiles from pool surrounds Dispose of all waste off-site Grind/clean slab after removal Inspect and advise on slab condition 2️⃣ Surface Preparation Grind/clean concrete substrate Remove contaminants and adhesive residue Prepare slab suitable for external waterproofing and tiling Form correct falls away from pool 3️⃣ Waterproofing Supply & apply external-grade waterproofing membrane suitable for: Outdoor use Pool surrounds Salt pool exposure Waterproof entire tiled area Turn the membrane up at walls, steps, edges, and penetrations Install in accordance with AS 3958 and manufacturer specifications Provide: Waterproofing certificate Product data sheet Installer warranty 4️⃣ Tiling Lay outdoor-rated porcelain tiles Slip rating P4 or P5 Use external-grade flexible adhesive Install movement joints and flexible sealant Neat cuts around pool edge, drains, steps, and penetrations 5️⃣ Grouting & Finishing External UV-stable grout Silicone to movement joints (colour-matched) Final clean and haze removal Seal tiles only if required by tile manufacturer Tiles Porcelain tiles only Outdoor / pool rated Size 300x300 to be confirmed (open to tiler advice for budget efficiency) Option for Tiles supplied by owner, quote saparately Requirements Proven experience with external pool surrounds Compliance with AS 3958 Waterproofing certificate required Public liability insurance Photos or references of similar work Pricing Please provide: Lump sum quote Separate line items for: Slate removal Waterproofing Supply Tiles Tiling labour Clearly state exclusions (major slab repairs, screeding, coping replacement, drainage works) Site Notes Good access Outdoor work – weather dependent Owner builder on site Looking for reliable, professional workmanship, not rushed or shortcut jobs

have replaced old toilet but need it removed. It is sitting in our apartment courtyard. Ground floor, No stairs.

install floor tiles for the whole house except toilets and laundry. we already ordered 600x600 porcelain tiles, just need installers, need a quote please

4m x 10m and 3.5m x 4.5 m ourdoor areas need to install dry lay porcelain pavers.

have recently laid porcelain glossy tiles and they've got some minor light surface scratches. Need someone to clean and remove scratches if possible.

I am seeking quotes to remove and replace failed sealant in the expansion/movement joints on my alfresco tiled area and steps. The tiles are stone/porcelain, and the existing joint sealant has deteriorated and separated between tiles and along the step edge.

Need someone to properly refit a double power point/GPO into a stone benchtop/splashback cut-out. The stone has already been cut to fit the power point, but the outlet needs to be secured properly so it sits flat on the stone.

Cover existing glass splashback with villaboard then tile over with Kit Kat style tiles. Splashback is 690mm x 2190mm.

Tile between floor cabinets and wall cabinets. Around 5 power outlets and window. Approx 5mx500; 3.63x600 and 1.8x33. And splashback to 500mm wide laundry tub Price neg

Install splashback 600 x 4650mm kitchen Install splashback 500 x 1200mm vanity Subway tiles are supplied, laid horizontal, while you provide skill and supplies to complete the job.

Remove standard glass splashback to allow area to be re-tiled. including disposal. Quotes negotiable.

Tiling of kitchen splash back

1. Floor tiling: Tile over existing floor tiles (no removal needed) Small laundry area Cut tiles neatly around: Floor drain Cabinet edges Ensure proper fall toward drain Grout and silicone edges (around cabinets/walls) 2. Splashback tiling: Tile wall from benchtop to underside of cabinets Cut neatly around power point Straight alignment and clean finish Materials: I will supply tiles Tiler to supply: Adhesive (suitable for tile over tile) Grout Silicone Notes: Cabinets and benchtop already installed Small area, but requires precise cutting Must have tiling experience

* Kitchen splashback (approx. 2.5m x 0.6m) * Small bar area (approx. 2.4m . 0.5 Requirements: * Clean, modern finish (straight lines, neat grout) * Experience with kitchen splashbacks * Attention to detail is important Materials: (select one) * I can supply tiles

Hi there, I’m looking for an experienced handyman, cabinet maker, or kitchen renovator to help uplift my kitchen. Scope of work: * Replace existing kitchen cabinet front doors with new ones in a brown or dark moss wood finish * Supply and install * Install a tiled splashback (happy to discuss tile options or outsource it separately What I’m after: * A clean, modern finish that elevates the overall look of the kitchen * Advice on materials, colours, and durability * A quote including labour and materials (or separate pricing if preferred) Additional details: * Flexible with timing but would prefer completion within a reasonable timeframe * Photos of the current kitchen in black attached and the other two images are AI generated Please include: * Examples of similar work you’ve done * Estimated timeframe * Your quote or rough pricing guide Thank you!

I am looking for an experienced tiler to install a kitchen splashback. The area is approximately 3.5 square metres and the surface is prepared and ready for tiling. Pattern of tiles shown in the attached image Area: Approx. 3.5 sqm. tile size : 600 mm x 300 mm Cut-outs: There are 4 double power points/switchboards that require precise cuts. Materials: I will provide the tiles. You will need to provide adhesive, grout, and spacers Apply silicone sealant to the benchtop/splashback join for a waterproof finish.

I’m looking for someone to remove existing splashback tiles in my kitchen. Approx. 2–3m² total (both sides of a small galley kitchen) Standard wall tiles Easy access, ground floor (no stairs) Important: This area will be covered by a porcelain slab splashback, so I don’t need a perfect finish. I just need the tiles removed and the wall left reasonably flat (no large chunks missing or major damage). No need for full plastering or repainting. Please bring your own tools and remove debris. Need this done on 27 April

Looking for an experienced tiler to complete a kitchen splashback installation in a small apartment kitchen in Manly. ⸻ Scope of work: • Tile splashback across two walls (L-shaped kitchen) • Total tiling area: approx. 3.0–3.5m² • Includes cuts around window, corners, and cabinetry • Walls will require preparation/rendering to achieve a flat surface before tiling ⸻ Tiles: • Supplied: 75x300mm ceramic subway tiles (matte white) • Layout: horizontal stacked (clean, modern finish) ⸻ Materials: • Tiles supplied • Tiler to provide: • Adhesive • Grout (white or very light grey) • Spacers, trims, and any required prep materials ⸻ Finish expectations: • Walls to be properly levelled prior to tiling • Clean, straight lines with consistent spacing • No lipping, flush finish across all tiles • High-quality finish suitable for a newly renovated kitchen ⸻ Location: Manly, Sydney Timing: Ready to start ASAP ⸻ Please include: • Photos of previous splashback / subway tile work • Confirmation of what’s included in your quote (labour, materials, prep)

I’m looking for an experienced tiler to install large format tiles for a kitchen splashback. Material details • Tile size: 600 x 1200 mm • Tiles will be supplied by me • Splashback area for kitchen wall and window (sill and side wall) • I’m happy to purchase grout and adhesive if you let me know what is required. Requirements • Experience installing large format tiles • Ability to cut tiles neatly for powerpoints/switch openings • Professional finish for kitchen splashback work Timing My schedule is a little flexible as I’m currently waiting for the stone mason to complete the benchtop measurement and installation - expect to be done in the next week. Hence the work will likely be late next week or early the following week. Measurement / site check I’ve already done a rough measurement for tile quantity. A site visit is welcome which I assume it would mainly be to confirm layout and check details before installation. Please provide a quote for labour and let me know your experience with large format tiles

Resealing needed between the bottom of my range hood and the tiled splash back in my kitchen (wear and tear). Remove old silicone. Clean and Prep. Apply new, appropriate heat resistant silicone. finish needs to look neat and tidy. Pls quote Inc. materials.

Removal 4 mirrored splashback Removal wallpaper Patching and painting where patched

I will supply the tiles - see photos for details. Tile kitchen splash back approx 1m2 area in total. Also tile bathroom inset strip drain. Located 45 mins north of Sydney harbour bridge

This is a tiling work for a laundry splash back. The tiling area is about 3.40 sqm. Tiles photo is attached, 6-sided (hexagon) tile, and tiles and grout are provided. We will need to cut the tiles Thanks

Tiler needed - kitchen flashback tiling. 3.2 m squared across 3 walls. Tiles provided, 10 x 10 mm, 8 x boxes of 50 tiles. No grout provided, grey grout required. Kitchen will be ready for tiling by Wednesday 14.

Hi there, I need an experienced tiler to install a kitchen splashback at my home in Hillsdale. Details: • Location: Hillsdale • Splashback area: standard kitchen (U-shape) • Tiles supplied: Newport Matte White Subway 75×300 • Grout: white (or happy to take your recommendation) • Benchtop already installed • Please supply adhesive, grout, trims and tools Please include in your quote: • Labour • Cutting around power points • Clean up and silicone finish Ideal install time: asap Site visit for measurement welcome.

Hi, need help with finishing the removal of a small cupboard utility sink splash back and sanding/grinding down the screeding (ready to paint). Other jobs in this utility room also to be discussed if interested and within capabilities, job required asap!

Quote on new bathroom tile en suite. Floor and walls. In Balmain - job is July 2026.

Hi Bathroom tiling - new small en suite, bathroom requires tiler. Must be experienced, reliable, have good reviews and be able to work to a schedule. Balmain based second week July. On site quote.

Need an experienced bathroom resurfacing specialist to refresh an older bathroom. Scope includes: Spray resurfacing wall tiles Bathtub resurfacing Floor tile coating / repainting Regrouting where required Remove and replace silicone Professional spray finish preferred (not hand brush finish)

Bathroom Tile Resurfacing / Cosmetic Refresh – Bondi Looking for an experienced bathroom resurfacing specialist or spray painter to refresh a small apartment bathroom in Bondi. The bathroom is structurally in good condition and I am hoping to modernise it on a budget without full demolition or changing the layout/plumbing. Interested in options including: * Tile resurfacing / spray painting * Bath resurfacing * Regrouting / resealing * Cosmetic modernisation Looking for a clean modern finish in a light neutral colour. Please advise: * Experience with bathroom tile resurfacing * Products/coatings used * Estimated durability/longevity * Approx timeframe * Whether preparation and materials are included Would love to see photos/examples of previous bathroom refresh projects. Small apartment bathroom located in Bondi. Flexible on timing.

Hi, I am looking for a quote to install thin tiles over an existing microcement bathroom floor. The bathroom size is approximately 2m x 3m.

1× Small bathroom and separate toilet renovation. Removal of old tiles, new tiles to be placed on floor and walls. Will supply tiles.

cut and set 600mm tiles in Bathroom grout and clean to finish

Replace 3 bathroom tiles. I have the tiles. You remove the damaged tiles, cut and install the new ones. I will finish the job - ie grouting and sealing. So only one visit. $100 per tile - $300

14 sqm tiling and waterproofing in granny flat.

Tiling bathroom floor and walls 1.8X1.5 and hight is 2.6 i will provide tiles and adhesive so just labour work

Replace a cracked tile on a wall in a bathroom. I have matching spare tiles.

Looking for an experienced tiler or handyman to replace a broken ceramic soap holder in my bathroom wall. The current holder is cracked and needs to be carefully removed and replaced with a new one. Details: Tile size: 20.5 cm x 10 cm Wall is tiled (older style, beige)

I’m looking for an experienced grout specialist to regrout two bathroom showers floors and bottom line of tiles on the wall. The grout in the shower tiles and bottom wall tiles has developed mold and needs to be carefully removed and replaced with new grout. One shower is in the main bathroom and is larger(116cmx113cm) than the ensuite shower ( 85cm x 90cm). I need a skilled professional who can complete the job properly without causing any damage to the tiles.

Bathroom demolition. Tiles and fittings removal

Tiles coming away from ceiling and I want them retiled .

Secure and grout a singular fallen tile from the top of a window frame in the bathroom. Preferably over the weekend, can cross check timings through the week.

My new shower and the rail is larger than the old one and I need new screws and the attachment drilled into tiles. Must have experience with tools and bathroom tiles, really don’t want it cracked!

my upstairs bathroom has a tile that has broken. it is not inside the shower, it is outside it. i suspect there’s an issue with how the tiling was done

We snapped a screw from our towel rail which we can’t get out. Need someone to remove old screw, fill hole and drill a new hole above it.

I may need replace the 2-3 tiles with cracks or just use water proof grout to seal the tiles. And just re grout all the tiles where you can see the grout is missing. Most importantly the lower area will need grout in it. Also double water proof.