Find a professional roller shutter repair in Melbourne

Manual roller shutter on single storey house, wire has broken so a new cable needs to be attached to the winding mechanism and the shutter itself.

Roller shutters got jammed does not go up or down can hear motor moving Located in Cranbourne North

I have two manual winder operated window roller blinds that have both broken. One has seized up and the handle will not wind in either direction. The other one the shutters have disconnected. See photos attached. This is on the first story balcony of a Victroian terrace house. As both blinds are locked down, external access is required via a ladder from the front of the house. I either need to them repaired, or if this is too difficult or expensive, then I would like to have them both removed. This needs to be done by a professional and not a general handyman. Please provide details of your past experience in repairing manual roller blinds. I have set a notional budget of $750 but this is not a fixed priced job as it needs to be diagnosed first.

Remove a security rollar shutter at the front of a shop

Hi, I need a roller shutter garage door adjusted so that it can be raised around 100mm. The door is currently sitting too low and needs to be lifted to allow proper clearance. Pictures will be provided for reference. Please bring any tools or materials required. Location: Coburg Timing: Flexible, but sooner the better.

Create custom made roller shutter support brackets for Mercedes X Class with Mountain Top MTR roller shutter. Preferably made of stainless steel. Open to suggestions Current roller shutter is rated to 75kg, looking to fit some brackets in the tub to support the shutter to allow a tent to go onto the tub.

Repair manual roller shutter - winding up to open shutter but stuck trying to close

Window roller shutter repair at house. Manually operated. The cable has come undone or snapped , needs to be reconnected to winder

After someone to come and repair our Somfy brand external electric motorised roller shutter. It has become jammed halfway, now is closed and won't open. The engine still makes a sound and is running fine.

1200 x 800mm manual winder window roller shutter is stuck in the "up" position. Requires fixing so I can wind up and down

Electric roller shutter was obstructed which jammed it while going down and it has since stopped working. Motor spins but seems like it's come off oys spool.

External shutter on upstairs window was removed and then refitted when we had our weatherboards replaced. We've since discovered two problems: 1) The frame of the shutter has been put back higher than it should be, this stops us from opening the window 2) The roller is stuck in the closed position and will not open. I can hear the motor trying but there's no movement. The external window/shutter is located on the first floor of a townhouse, access via ladder. Note roof is tiled so caution is required.

Roller shutter service as the shutter does not move.

I have an electric window roller shutter that is not working the machine is working because I can hear it but it’s not going up or down we opened it up to see what the problem is so I will have photos of it being opened from the top

Bedroom window roller shutter is not working. The motor is heard working when switched. It’s on the first floor bedroom

External window roller shutter seems jammed. Makes the typical noise but does not catch the rail and come down as it typically does

2 external Roller shutter require repairs

Just need them fixed, non electric $100 max budget no bargain 2 or 3 have to double check

I’ve a roller shutter on a second story that no longer lifts. It’s electric. The motor runs but shutter doesn’t raise. Need a service, repair or motor replacement? Not sure! The shutter is on a second floor inside an eve. It’s approximately 1.6m wide and regular window drop.

For inspection first. I have two roller shutters on my upstairs townhouse, one at the front and one at the back. The roller shutter at the front covers two awning windows, with the frame positioned between the centre of the windows. The roller shutter at the back only allows about 10 cm of the window to open, if that. I’m looking for advice and assistance on the best solution. Can the shutters be repositioned, such as angled, to allow the windows to open? Should they be removed, or is there an alternative solution? Photos are attached for reference.