Find a fence installation professional in QLD

Install a timber front fence with sliding gate.

40 m Wooden post and pool fencing Install single gate and double gate Must know what to do Ensure don't ruin irrigation and water pipes

The existing timber side fence (approx 1.5m above ground) requires the replacement of 3 timber fence posts to improve stability & general sturdiness.

Colorbond Fence - 1.8m (6ft) metre high x 28.70 metres long (genuine oxworks colorbond fence) Supply and Install Need to remove existing fence and build new one.

Erect 60m of colorbond fencing. (Material supplied by customer ) Existing fence to be removed and disposed

Need a self-closing spring installed into a front gate. I’m assuming the wall is concrete and the gate is metal. Need it to be installed properly so it lasts as we have a ‘dangerous dog’ that can’t get out of the gate is left open. Sprig already purchased!

Extend the current picket fence with three "Screenline" panels.

G’Day, I need two new side gates built and installed to a high standard. I’m after quality workmanship and materials that will stand up to years of outdoor use with minimal maintenance. Gate details Double gate: 3130 mm wide x 1770 mm high Single gate: 1660 mm wide x 1770 mm high What I want Strong, well-finished gates that will last Gates fully installed, hung and adjusted so they swing and latch properly Quality hinges, latches and fixings Materials supplied by you and included in the job price Happy to consider your advice on materials. I can send photos of the gate areas, and a site visit isn’t essential unless you think it’s needed. Message me with any questions. Thanks, and I look forward to hearing from you! Cheers.

20m spear top fence to be installed ASAP - Tomorrow all materials and tools on site

Our white aluminium slat side gate and a small matching fence panel were taken off so a machine could get in to build our pool. The pool work is done, and I need both put back exactly where they were. All the parts are on site. The job: - Re-fix the post and the gate's base plates to the existing concrete strip. The old bolt holes are still there, but new masonry anchors may be needed. - Rehang the gate on its existing hinges, then adjust it so it swings freely and the latch catches every time. - Refit the small slat panel between the gate and the dark timber boundary fence, including removing the temporary timber board fixed to the fence there. - Make sure everything is plumb, level, secure and tidy. Please bring your own drill, masonry bit, anchors or Dynabolts and fixings. The gate needs to swing shut and latch properly.

Replacing 10m of fencing with either wooden palings or colorbond. Quote for both would be great. Thanks

Need a small roughly 2 m wide color bond fence installed to extend an existing colorbond fence. One step to be allowed and two to three posts. Photos of the area are attached. Happy to pay what is required to get the job done before end of November. See attached photos where extension is required between the colorbond fence and white batten fence.

We have a double car gate which sits on an aluminium runner the wheel is scrapping and needs replacing gate is sticking

2 glass gates installed into both rock and wood

Build a fence around our existing bin area. The bin area has been concreted and we would like to enclose it (probably only needs 2 sides, 1 side is existing fence and 1 side can be left open). We have spare existing fence panels that can probably be used.

Require two fence support beams replaced and the fence re-fixed to it. It’s rotted at the bottom therefore not providing the necessary support. Want to avoid replacing the entire fence at this stage.

Installation of Lockmaster Swing Gate to existing fence. Swing Gate is provided. Installation required.

Glass panels are all slowly coming undone and wonkey as ground has moved and posts done align with glass any more. I have had a few panels done with additional spigot support but I want the lot done now: removing the posts and replace with spigots. 10-12 panels need spigots, depending on what’s possible on either end (might need to leave some posts in, especially with the door): I have sourced spigots already. Scope of task: - assess and recommend best way forward with the end and door panels - remove and replace posts with spigots: 10-12 panels - supply tools: to drill holes into tiles without wrecking them - other bits and bobs needed: bolts etc - remove posts from premises: dump run etc Location is Ipswich central. Thanks Oliver Edit: I just realized I did not adjust the budget since I had this task online last time given I have now sourced spigots already and they’re not included in task any more.

I need an experienced fencer to supply and install a compliant black metal pool fence and gate around the sliding-door recess shown in the attached photos. This work is required following a pool safety inspection. The fence returns are intended to sit close to the left and right sides of the sliding-door recess, generally in accordance with the inspector's concept sketch. Requirements: - Fence height: 1200mm - Latch height: 1500mm - 1200mm arc from the bottom of the fence outwards, which must not hit the step into the home - 900mm arc from the top of the fence outwards - Gate to be self-closing and self-latching - Gate must swing inward toward the house, away from the pool - Fence to be fixed to the existing timber deck - Final dimensions and installation method to be checked onsite The concept renders are indicative only and show the intended style/layout. Please quote for supply of all fencing, gate, compliant hardware, posts/fixings and installation. Please include examples of previous work if available. Please submit your offer for supply and installation based on the photos and inspector's requirements. There will be additional work available for the successful tasker if this job goes well.

I am looking for a carpenter to replace a timber side gate post and to rehang side gate please.