Find a fence installation professional in Newcastle

Install Colourbond Fence Height Extensions I am looking for a handyman or fencing contractor to install height extensions to my existing Colourbond fence. The fence extension panels have not yet been purchased. I am happy to either: - Purchase and supply the extensions myself based on your recommendation; or - Have you supply and install the materials, with the cost included in your quote. The existing fence is standard Colourbond fencing and I am looking to increase the height to ensure it complies with pool safety regulations. As the Colourbond fence forms part of the boundary/perimeter pool barrier, it is required to be a minimum height of 1.8 metres. The current fence height is approximately 1.3 metres. The estimated length of fencing requiring height extensions is approximately 20–22 metres. Please include in your offer: - Your experience with Colourbond fencing or fence height extensions. - Whether your quote is labour only or supply and install. - Any recommendations on suitable products or extension systems. I would like this work completed within the next two weeks. Please provide your availability and an estimated cost.

Replace 2 off colourbond fence post as marked in the photo. New post height will be 2.7m high. Reuse panels, timber and top rail.

Supply and install approximately 34.535 linear metres of 1800mm high Colorbond panel fencing along the left-hand boundary, starting from the back corner and continuing to align with the front of the building. Fence posts are to be installed with longer posts to allow for a 200mm x 50mm treated pine sleeper underneath the fence panels. Supply and fit treated pine sleepers underneath the fence line. Note: Fence length shown on sketch: approximately 34.525m / 34.535m along the boundary. Send me an estimated cost via message. Please note, it is completely flat land and straight boundary line with no slope.

Old gate is rusty I can get a new gate to fit but I can't remove the old one and hang the new one myself.

Installation of 27m side boundary fence. Installation required for vertislat fencing panels plus 1 gate. To be installed on top of concrete retaining wall. All parts required are supplied as noted below. Will also need to remove the old fence posts shown in the photos below. Slat-Fence Pool Safe Fence Panel - 2.2m wide x 1.2m high. Qty 12. Pool Fence Panel Fittings Set - 4 brackets with screws Slat-Fence Pool Safe Gate - 970mm x 1.2m Flanged (Base Plated) Fence Post with cap 1.3m - to bolt down. Qty 14 Raised 'Base-Plated Post' Domical Cover Plate - for Bolt Down Posts. Qty 14

Need old fence taken down and new one installed

Need a colourbond fence inside roughly 25m the fence is to sit on top of a retaining wall

Replace an existing wooden fence in front yard

Supply and install a timber fence, single paling, 3x rail at 1500 high and 13.9m long with timber posts. There’s no demolition. Also install a galvanised post where current fence is to strengthen fence.

Seeking quotes to supply and install non-timber fencing across 3 boundaries + a motorised sliding gate. Property is on a sloped block in a cul-de-sac. Photos attached. Please price all 4 sections separately (may stage works): 1) Side fence – replace existing (~18.3m) Max compliant height (up to 1.8m), stepped/raked to slope. I'll remove old fence; allow for old footing removal if needed. 2) Side fence – new install (~17.1m) Max compliant height (up to 1.8m), stepped/raked. Noticeable slope. No existing fence. 3) Front fence (~10.7m) Height/design to suit planning requirements. Must present well from the street. Existing low retaining wall along front boundary may affect placement/height — please advise best approach. 4) Front sliding gate (~5.2m opening) Motorised, remote controlled. Runs across stamped concrete driveway — advise on track solution and any cutting required. Advise if new electrical cabling is needed for motor. Materials: Non-timber. Solid infill for sides (privacy/security). Front open to solid or architectural/slatted if it balances privacy + street appeal. Dark tones preferred (Monument, Woodland Grey or similar). Colorbond, aluminium, steel or similar. Access: Excellent — driveway + neighbour's driveway + both sides of house. Neighbours supportive. Some vegetation near boundaries. Please include in quote: Itemised pricing per section Recommended materials/design All inclusions (posts, footings, panels, gate motor, remotes, hardware, sensors) Whether electrical for gate is included/excluded Timeframe, warranty, exclusions Council/compliance advice Licence & insurance details Examples of similar completed work if available Timeline flexible. Happy to arrange a site visit. Looking for a practical, good-looking, long-term solution.

Need a qualified insraller to finish work

2 Sections of Fencing needs replacement with same fencing material. Measurements are Section 1: 155cm High X 240cm Wide Section 2: 150cm Highest point tapering to 125 cm lowest point X 240 Wide

Hi, I need to have an old colourbond fence removed and a new one installed. The old one is rusted out and blown over. 6 Panels in total and the fence is level. I can supply all materials if preferred.

I am looking for a reliable handyman to install one Colorbond side gate. I have purchased everything required for the job; I just need a professional to handle the digging, leveling, and installation. Scope of Work: • Dig & Set: Dig two holes and set the gate posts using Rapid Set concrete (provided). • Install: Hang the gate (1000\text{mm} \times 1800\text{mm}) and ensure it is perfectly level. • Hardware: Fit the hinges and the latch kit. What I Have Provided: • 1x Colorbond Gate (1000\text{mm} wide) • 2x Gate Posts • Full hardware kit (hinges/latch/screws) • Bags of Rapid Set concrete Requirements: • Must have a post-hole digger or spade and a spirit level. • Experience with gate/fence installations to ensure a smooth swing. .

Fix the front gate as it is broken

Looking for someone to install snake/mouse-proof wire mesh along approximately 40-45 metres of Colorbond fence perimeter in our backyard. All materials will be provided. Open to advice, but initial plan is: - Mouse/Snake Mesh (6.5mm aperture, 90cm wide) (https://www.bunnings.com.au/jack-90cm-x-30m-x-6-5-x-6-5mm-mouse-mesh_p3068782) - Star pickets with zip ties for securing The job involves: - Hammering star pickets into the ground along the fence line - Digging a narrow trench along the fence base - Bending the bottom of the mesh into an L-shape and burying it as a footer to prevent digging under - Attaching the mesh to the star pickets with zip ties - Backfilling the trench The fence is Colorbond (shared fence) so no screws or attachments to the fence itself - again, open to recommendations if you see a better way to implement.

Looking for a custom made functional & aesthetic wooden (white or natural timber) baby gate for the top of our steep internal stairs (approx 1.05m wide). Open to swing or sliding options. Photos attached for inspiration.

Install dual gate opener - power already at the gate - plug and play model

Put damaged fence panels back in

I need these screens x 2 installed on my fence to give it height for more shade in my backyard