Find trusted local electricians in Outer South West Sydney

Needing trees cut due to solar panel installation Please see photos

Click noise coming from the garage (similar to a light switch clicking). It happens when it’s windy and raining. I can provide a video shows the click noise from garage.

We need a licensed electrician to attend ASAP to inspect and fix an electrical issue. Three breakers have tripped (workshop lights, toilet, and office area), and the lights in those sections are out. The switchboard is clearly labelled, and we have photos of the affected section available. Availability: Ideally today. Thanks – looking forward to your response

Quote to install power points and relocate ceiling lights in existing property as per attached

Scrap metal yard will give you another $30-40 upon delivery. 135L gas Hotwater tank has been replaced I have left the system at the kerb for easy removal. The early the better for this one. Cheers

Need a power point moved

Changing one bulb and one downlight

2x bathroom heaters need replacing, new units are purchased. Old is HPM 2 lights. New is Clipsal 2 lights. Both ducted. 2 x fire alarms replacement.

Need to replace Rheem 27 water heater to Rinnai infinity 32L Rinnai REU-VRM3237WG-50-AK

#Install 2 x power points - kitchen/ lounge room back to back #change 2x fluoro round ring lights to round LED lights #Upgrade 2 single light switches # down light installed under a cupboard in kitchen #Fix a fan switch - high and low work not the med #install Power point - front outside #install Sensor light -front outside #Shed light installed out the back

Supply and replace five gimble led lights in kitchen two are 3 meters high and fix power point to glass splash back

TASK 1- In my bathroom I have an IXL Tastic product which is a 3 in 1 heat, fan and light The light switch has stopped working. The fan light and heat light is still working. Please refer to picture. I have replaced the light, and the light switch does not work so the problem must be something else. Need someone to investigate and rectify. TASK 2- Tried replacing my long tube lights. When I turn on the switch it's not working. I may have broke it. Need someone to take a look.

Smoke alarm makes noise. It needs to be replaced. Suppy and install required. It is wired with electricity.

Hi Fellow Taskers I'm looking for a qualified/licensed electrician to complete some small electrical works. The following jobs have also got photos attached. Supply and install 2x new power point in laundry area (likely) via conduit running on exterior. Find multiple photos interior and exterior for reference. Install/replace exisiting power point with customer provided board. Replace/repair existing point in wall. This power point is not sitting on a support. Please send offers acknowledging the works as provided in above scope.

Various electrical jobs - - Put in 3 down lights (supply and install) - install 2 pendant lights (pendants supplied) Wires in place. - take down 2 glass pendant lights and replace with 2 large rattan pendants (high ceiling - no way to measure but my estimate is around 3.5 metres. Kitchen bench underneath. - take down a pendant and replace with one of the pendants from Job above Single storey home

3 fan-light switches to be replaced. Have the switches already. Also have an outdoor dryer that needs to be hardwired or a new powerpoint installed outside, currently the nearby powerpoint trips circuit breaker as its on same line as solar hot water.

Change the battery in a smoke alarm

I have already ran the wires from the back of the oven to the eve right on top of switchboard. I need a QUALIFIED electrician to connect it up. You will need to provide necessary switch please include that in quote Please provide availability details when making offers I don't live at that address and will have to meet you out there There will be other work around the house once this is sorted that we can discuss

I need a Generator Tool Box installed on a caravan. I have most of the bits needed, I have a small base made up that might be good if welded to the supporting bar coming out of the chassis. I am no expert so will rely on the tradie for advice. There is a hardware up the road and I am happy to go any get other bits as required. You will need own tools cutting and grinding, welding, etc.

I've got two existing fire alarms in a double storey house. I need to get the old ones replaced and new ones installed. Don't need to be interconnected but that is fine if they are. Should be a relatively simple job. Cost includes both labour and for cost of the fire alarms.