Find trusted local electricians in Ingleburn

I would like a plug on a heated out door vortex spa repaired please as my ex cut through the cord with a lawn mower. I also need a tubular light fitted for my garage as the one I replaced it with doesn't work. Unsure as to why. ASAP please. Thank you.

Granny flat attached to main home to be wired up. 7mx 6m room

Hi there, I need a fully licensed electrician to swap out my current electric cooktop. I am replacing an existing 70cm Baumatic cooktop with a brand new 70cm Smeg cooktop. The Job is Straight-forward swap. The cut-out size is already correct (both are 70cm), and the necessary wiring/connections are already in place. I will handle the disposal.

I need a 3 phase power point installed. The building has 3 phase. I need the PowerPoint installed next to the box.

Hi, I’ve already bought all the materials: • 8 double power points • 3 switches (replace only) • 3 outdoor waterproof power points • 1 outdoor sensor light • 1 ducted bathroom exhaust fan • 1 ceiling light (replace only) You just need to do the wiring and installation. My house is double storey, so you’ll need a ladder about 7 metres high. Please send me your price for the full job in one day and let me know when you’re free. Thanks, Jacques

I need to replace 2x smoke alarms. The somke alarm is purchased and ready to be installed

I need to swap around these two plugs. 10 minute job. No hardware needed. Please just swap these around for me.

Installation day - from 27th Dec till 2nd Jan. I live in a townhouse in Ingleburn, bedrooms are in 1st floor. Brick wall outside, gyprock inside. I bought a 2.6kw split ac for my bedroom. Please check the photo. You will need to get on the roof of the next unit attached to my townhouse to fit the outdoor unit. There is a power point on the same wall inside the bedroom. back to back. Please quote your installation price including bracket. Thank you.

I bought a simple LED light to be connected in our bedroom ceiling where the line is already there.

My current switchboard is very old, has asbestos backing, and still uses ceramic/rewireable fuses. Every night the power trips and I have to reset a small switch manually. I want the entire board upgraded to a modern, safe, compliant unit with RCDs/MCBs, including safe handling of any asbestos. I want to ensure the power trips do not occur. I also need help fixing a switch in the kitchen area, and I have a pool light that works but is currently floating in the water — it needs to be secured or properly mounted. Scope of work: Inspect existing switchboard and identify cause of nightly tripping Safely manage/handle asbestos components (if required) Replace old fuse board with a new compliant switchboard Install modern safety switches and circuit breakers (RCD/MCB) Fix or replace faulty kitchen switch Inspect pool light and secure/mount it properly Test all work and ensure full safety compliance Provide an electrical compliance certificate after completion

I want to change three phase power points. I currently have a 3 hole switch and want to make it a 4 hole

There are no Downlights currently. Would like to replace low hanging lights with Dow lights. Remove old ceiling fan Living room - currently 2 lights and a fan. Would need to install 6 new lights and remove the fan Kitchen - one oyster light and 3 other lights- would like to replace with 6 down lights Bedroom 1 and 2 - currently 1 ceiling fan and light. Would need to replace with 4 down lights Bedroom 3 - currently 1 light- would need to replace with 4 down lights

We have a handful of pigeons who have created nests under our solar panels. We would like them removed + have the solar panels bird proofed so that they do not return to make new nests. We are animal lovers though, so ideally this could be done in the most humane way possible.

I have a diesel 10kva single cylinder genset. Not starting. Battery is fine.

Electrician for the installation of LED downlights

I have an old Ness 5000 home alarm system that hasn’t been used in years. After a recent power outage, the siren started going off. The backup battery is dead and I don’t know the code, so I just want the system fully decommissioned/disabled. What needs to be done: Confirm and identify the mains transformer (I’ve added photos – it looks like a white brick-sized box near the alarm panel, but I’m not 100% sure). Safely unplug or disconnect the transformer so the panel no longer has mains power. Open the alarm panel and disconnect/remove the dead 12V backup battery inside. Disable/disconnect the siren so it cannot activate again. Leave the system completely powered down and silent.

One of my power point on the wall is not working and need it replaced

3 Electrical Jobs- a) Replace Existing Outdoor Sensor light. b) Replace Existing Bathroom Exhaust c) Connect Bathroom LED mirror light to the nearby switch( please check the back of the mirror for the wiring type) Installation Time- Thursday 9AM-11:30AM.

Need entire solar water heater system removed. Panels, plumbing and everything thats connected to it. Thanks.

16 downlights on existing lights supply and install