Find trusted local generator repair services in QLD

Generator not making spark

Task: Install new Generator wiring and connect to House at Yarrabilba 4207. Generator: Purchased. Need installation by a licensed electrician. dedicated inlet, transfer switch, and circuit protection. Electrical Task Requirements:- Install a 32A inlet box outside.- Wire a manual transfer switch. Scope of Works • Ensure compliance with AS/NZS 3000 wiring rules. • Suggest location of Generator – outside. • Use 32A cabling and breakers to match generator output. • Manual transfer switch (Generator is not ATS). Install at the main switchboard. Ensure that safe switching between grid power (Energex) and generator power. Ensure no dangerous back-feeding. • Install circuit breakers & RCDs (safety switches) if relevant (already installed as standard) • Wiring & cabling, heavy‑duty 6mm² or larger cabling for 32A inlet. Proper earthing to generator frame and house earth bar. Conduit for outdoor runs. Suggested wiring: Flow from the generator’s 240V output through a 32A (heavy‑duty cable) outdoor inlet box, into a manual transfer switch, into house breaker panel powering selected circuits. Electrical Compliance Required: Compliance with Australian standards - Licensed electrician required, experienced with wire transfer switches and inlets. - Certificate of Testing & Compliance must be issued after installation. - AS/NZS 3000 standards for wiring, earthing, and RCD protection.

Not sure what is wrong. Fuel or electrical

Supply and install the following; - Weatherproof 32A single phase inlet plug mounted on wall for generator connection (full house supply). -Generator changeover switch and overcurrent protection. - Changeover switch to select between normal and controlled load for Hot Water System (ie to allow HWS to run from Generator)

Open roof cover to span pool pump and generator - timber frame and roof sheeting. Budget a guide

The outlet from the fuel tank has broken directly where the hole in the tank is I require replacement

install power point in meter box to connect generator during power outage, do not require connection for hot water, air-conditioning only essentials.

I’m looking to have a generator inlet socket and changeover switch installed at my home so I can safely connect a portable generator to my main switchboard during power outages.

Service generator Repair pull cord Servuce edge trimmer

Add a generator breaker and plug to power box

To start this generator so it can be used.

I need this generator running so It can be used.

Will not start ...bought new ..petrol good, battery good

Paguro 4000 - generator service (need spares) Mercury 4hp four stroke - service and carby replacement (to make 6hp)(have carby with me)

Home Generator won’t start, have replaced battery and fuel. ?

GENERATOR 11.85kVa Inverter Electric start - PETROL Part No.: GSC12000iY Code 1 . Generator cranks but does not start. No spark, no petrol.

I have a panther 3500w generator that could do with an oil change and a once over.

We have a GENTRAX GTX4200 Inverter Generator that recently won't start. We have been using it for maybe half a year. We have already tried replacing the spark plug (which was already replaced around a month ago - so might not be the issue). We reached out to the warranty provider and they suggested carburetor cleaning. We have been given instructions and attempted but could not progress far enough to take it out. Will include a picture. Alternatively, there is a chance we have added too much fuel and 'flooded' the carburetor (from researching online). We don't purposely tilt it but we are parked on an inclination. This was the video demonstration provided to the warranty provider so might as well attach it, if it helps https://streamable.com/4f2i4y **Update** Unscrewed the carby bowl to drain the fuel. Also did the spark plug test for ignition/spark (with it disconnected). Managed the get the generator running for about 30 seconds. However when starting it, it felt different than when it works properly. Choke position out, two pulls, almost seems like it will go but doesn't. Immediate tried choke position in and pull and it runs. After about 10s there will be unusual 'putt' noises before the red signal and it turns itself off, along with a last puff of smoke and bad smell. We have sprayed 'Start ya bastard' - removed the bowl and sprayed into that entrance. Choke position out, 1st pull, seemed to almost start, pushed the choke in and it started to run. but again, for only 30s with similar observations. We are in Chapel Hill, but we are able to come to you with the generator and also flexible with the time (including evening).

Model: GENTRAX 4.2KW Inverter Generator Fix my GENTRAX 4.2KW Inverter Generator. I have already checked the engine oil and replaced the spark plug, but it still does not work. Looking for someone with experience in inverter generators who can diagnose and repair it.

Yamaha Ef2000is generator won't start. Little used but hasn't been used in a few years. Put new fuel and oil in and new spark plug but won't start. Maybe carburetor needs cleaning?