Find local electrical rewiring electricians near you

I have vintage European lamp that has been flickering, so I want to take the opportunity to get it rewired with an Australian plug. I'm also wanting to lengthen the cable – it's currently 73cm long and I would like it to be about 2m. I don't have any of the supplies to do this, so I'm hoping the longer cable and Australian plug can be included in the quote! Must be a licensed electrician.

disconnect wires from board of a solution 862 alarm and reconnect to konnected alarm panel pro

Existing video intercom has been installed but wiring has issues (electrician tested and noted products work fine but there is a fault Wiring needs to be replaced using existing conduit (or replacement where this is needed).

Need help with the electrical rewiring due to renovation in an apartment. Please send a quote or stop by to see the job.

3 bedroom apartment under full renovation. Price is for one eight hour day with materials either supplied or paid on top. CBD location with free parking for vehicles up to 1.95m. Change wiring, board, powerpoints, switches, downlights, etc.

We have a table lamp and a broken floor lamp that need rewiring. Table lamp needs new lamp holder and retaining ring (maybe new lamp holder). Floor lamp needs a new lamp holder and new internal cord.

I need a lamp of mine, a vintage double header, rewired. It’s flickering when I on switch it on so have unplugged it awaiting a new cord.

needing the lamp updated wiring for inside and outside lamp sockets, the inline switch is new and i would like to keep that.

I need to install two small pendant lights under 5kg each, one larger, one small. Both need new wiring because the wire is old and skin is failing (approx 15m each from light to switch and to switchboard). The lights are located very close to the manhole. I’d like a noggin installed in the ceiling cavity for support. The lights are just 2 meters away from manhole. So it's easy to access. Because the house has tenant living needs electricity before 5pm, the job must start after 5pm. I estimate would be a 2 hour job it will be good if finish before 7pm.

Have fitted a new exhaust on my Subaru, one sensor reaches but other is in the middle of exhaust and need an extension and re wire as old one is too short. Runs from engine to mid exhaust, seems like it’s a deutsch plug connector to original o2 which I still have.

I want new lights and wiring on my 8x5 trailer. Supply and install new lights with number plate light and rectangle plug.

We have installed Philips hue downlights but 4 of the old lights were on a circuit with a dimmer. So now those hue lights flicker on and off. So we need to rewire the switch circuits on this panel so that they work with the new lights and not the old ones.

Dog dug up and chewed some wiring about a year back need some1 to fix/replace . Repost of a job as last 1 did not go ahead

I have a lamp from the US I want to use in Australia. Needs an AU plug and advice on bulbs due to voltage/current differences.

I have a 1950s-60s era vintage floor lamp that has had the power plug cut off it. I require a registered electrician to rewire the lamp, attach a new power plug and test that it’s operational and safe. Please note that I don’t have a replacement power plug but can buy one under your direction or you can provide it and this can be added to your Airtasker fee. Please only respond to this task if you’re a registered electrician, thanks!

I need two 70s wooden standard lamps to be rewired. Both have bayonet sockets for bulbs that look in good shape. Both have had cords cut at the base. I don’t have the replacement cord or wall socket. I’m in Wanniassa but I can drop these off Southside, especially Fyshwick.

Outdoor light rewired and outdoor sensor light installed

Outdoor fan - just needs a new remote rewired. We have the new remote. Just need to replace the receiving device in the fan. Low ceiling. In an alfresco area.

I have two vintage wall sconces that need repairs. One seems to have the wiring already and a switch, the other has no wiring and no cord/switch at all

Looking for help to replace the light in an old (70’s) bar cabinet, which has internal wiring. It’s likely that the current light is no longer manufactured. I will pay for materials on top of airtasker fee.