Find local NBN electricians near you

Install 2 new power points: - Bathroom - through tiled wall - Laundry room 1 Ethernet wall point: Living room for wired computer connection Relocate NBN connection: Currently located in kid's bedroom. Need to relocate to living room side on the same wall or opposite side of the living room (whichever cost less).

Install 2x30-40A Power Lines + Optical Drop + Network Cable to Backyard - Edmondson Park Licensed Level 2 ASP + Electrician needed. Professional, compliant, insured work only from 3-phase meter + NBN cabinet. Exact Scope: Run/install 2x 30-40A power lines from 3-phase meter to backyard (connection may already exist - verify/confirm first I need this to power my server rack and need some grounding for the rack too Install optical drop (fibre (sfp attached)) from inside the house NBN/security cabinet to backyard Run Cat6 network cable from same NBN/security cabinet to backyard All work AS/NZS compliant, fully tested + certified Provide compliance certificate Location: Edmondson Park (exact address on booking) Requirements: Level 2 ASP licence for NBN fibre work Fully licensed/insured A-Grade electrician Experience with 3-phase power + optical drops Photos of existing 3-phase meter + NBN cabinet provided to selected tasker Need a regular power point dropped in the jist behind the rack.

Electrician to run nbn data cable from garage to house through ceiling

We had our journey accidentally cover over our nbn cable and need a whole cut in the plywood to get cord to connect internet

Updated scope:Revised from6A to Cat6, with 7 runs, a mini patch panel, PoE camera mounting, and NBN FTTP conduit/draw wire pre. Looking for an ACMA registered cabler for a domestic networking job in a single-storey house. Scope: - NBN FTTP conduit / draw wire preparation: Prepare or use a suitable conduit with draw wire from the Far Wall entry area to the Garage Near Wall, approx. 6–7 metres. The Far Wall has no power, so the NBN box needs to be installed near the existing power points on the Near Wall. NBN FTTP is not yet installed; this is for the NBN technician to pull fibre later. - 7 x Cat6 data runs, all terminating at the Garage Near Wall: - Lounge x2 on one double RJ45 wall plate: - 1 x Lounge-WAN / NBN to Router - 1 x Lounge-LAN / Router back to Switch - Bed 4 x2 - Bed 1 x1 - Bed 2 x1 - Front door CCTV x1 for PoE camera - Garage termination: Install a small Cat6 mini patch panel at the Garage Near Wall, preferably 8-port or 12-port wall-mount type. - CCTV: Mount 1 x PoE camera on the eaves near the front door. Please include drilling, mounting and basic weather sealing if required. - Materials: Please supply and install solid copper Cat6 cable, RJ45 wall plates, keystones, mini patch panel, labels, conduit/draw wire materials if required, and all fixed cabling materials. Please do not use CCA cable. - Testing and labelling: Label both ends of every run and perform basic testing on all Cat6 runs. Please provide photos or test results showing each run has been tested. - Hardware supplied by me: - Switch - Router - PoE camera Requirements: - Must be ACMA registered and insured - Upon completion, please provide a completed TCA1 or equivalent - Please confirm the 6–7m NBN conduit/draw wire preparation from the Far Wall to the Garage Near Wall is included in your quote - If any additional work is required after inspection, please advise before starting

Following NBN’s conduit installation guidelines, cut concrete, excavate and install a communications conduit, and backfill for a new build house in Enoggera. Scope of work: - Saw cut and remove approximately 1m length of concrete footpath adjacent to the house, approximately 200mm wide, straight cuts with clean edges, no jackhammer-only rough edges - Remove and dispose of concrete - Excavate trench (300mm deep) in the lawn (approx. 4m length) from the property boundary (as shown on photo) to the house external wall (directly below PCD location) - Provide ~50mm sand bedding under conduit - Supply and install heavy-duty orange communications 25mm conduit - Supply and install a draw string throughout the conduit - Install long sweep bends only (no sharp elbows) - Backfill trench appropriately after installation (except 300mm from both ends) - No need to reinstate concrete Specifications (must comply): - Minimum conduit size: 25mm - Minimum trench depth: 300mm - Minimum 50mm sand bedding under conduit - Backfill with clean fill/sand (no sharp rocks in contact with conduit) - Work must comply with NBN Co guidelines Prior to fund release, photo evidence is mandatory: - Entire open trench (before backfilling) - Conduit placement and bedding - Both ends of the conduit - Depth clearly shown (with tape measure) - Concrete cut

Require cable conduit ran for NBN install, external box location to inside the building, terminating at inside NBN box location: - Punch through single brick external wall into front door entry way (for NBN to place the external NBN box out of elements) - Run conduit from above mentioned location within entryway up wall and into roof (approx 2.5m) - Run conduit through roof (approx 6m) - Run conduit down wall inside the building (approx 2.5m) to where NBN inside box will be - There is no requirement to chase any conduit between double brick - Roof cavity is accessible via manhole inside, via a tall ladder - Needs to be self sufficient with regard to all tools, ladders, PPE etc - Materials possibly able to be supplied prior to install, pending discussions (self sufficient with materials is preferred, however) Estimated materials needed: - 11-12m conduit - couple of elbows and/or 45s - 11-12 conduit saddles + fixings (masonry + timber)

Need electrician to move NBN connection point from bedroom to living room. Move is about a 1m but need to take cables to different wall and put in the tall boy in living room.

Need someone install a telephone port in our house, there currently isn’t one but there is a Telstra box installed outside. (Old Queenslander) this will involve running cable from the Telstra box and installing the new port for our NBN modem to be plugged into

I need a approx 20m trench dug for an NBN conduit to the house. Needs to be 400mm deep the whole way. Would be an easy job for someone with a trencher. Send me offers, not sure of costs.

hole in wall where my NBN cable comes out

The NBN cable does not have a proper cap on it, so the wire is exposed and comes out of the port easily. Please supply the proper cap and install on the cable, ensuring it plugs into the NBN port.

I need to reinstall my NBN FTTP box (NTD) on the wall. The box is already onsite. It just needs to be mounted and connected. No battery backup unit required. No NBN technician required – only physical reinstall. Tools for wall mounting required. Flexible with day and time.

I need an Ethernet port installed from my NBN box in my garage to my downstairs living room. There are existing Ethernet ports located upstairs. Double storey house.

Need help connecting my NBN modem to pre-existing connection. Have tried to do it myself with no luck! Hopefully should be straight forward for someone more tech savvy! Have included photos of my modem and connection point as best I can.

We need someone to dig a ca 8m trench for an NBN conduit. It needs to be 30 cm deep and runs from the house to the boundary. Ideally we want to keep the grass to cover it again. NB: the photo shows the front of the house. The trench needs to be slightly to the right. It’s a clear strip from the house to the boundary.

Need a certified technician to install an RJ11/NBN wall socket for internet access. The apartment only has an old 600-series telephone terminal. There is no modern RJ11 or NBN-ready socket installed.

I have FTTP NBN with the NBN fibre box (NTD) located in the garage. Currently, my router connects via ethernet to a data point downstairs (study). I want to keep this existing downstairs connection and add a second Cat6 ethernet point upstairs so I can relocate the router out of a new nursery. Scope of work: • Run one additional Cat6 ethernet cable from the NBN box in the garage to an upstairs room • Install one ethernet wall plate upstairs • Keep the existing downstairs data point active • Terminate and test the new connection House is two storey. No NBN or ISP work required. Licensed cabler required.

Hi there 👋 I had an NBN fibre upgrade appointment, but the technician couldn’t complete the installation because I wanted the indoor NBN connection box/modem installed in my closet (where my current setup is). He said he couldn’t use the existing cable path as it runs inside the brick facade, and therefore couldn’t get a new fibre through to that point. He also didn’t install the outdoor unit for the same reason. He advised me to get a licensed electrician/data cabler to: Create a new cable path or conduit from outside (where NBN will mount the outdoor unit) to the closet where I want the modem. Ensure the cable route is ready for NBN to return and complete the fibre connection. Job details: Single-storey brick home 🏡 Need neat, NBN-compliant cabling or conduit installed Easy access to both outdoor wall and closet Just need the cable path ready — NBN will handle the fibre install once this part is done Timing: Flexible — weekday or weekend is fine. Please quote only if you’re a licensed cabler or electrician experienced with NBN fibre or data cabling. I have attached pics of existing connection from outdoor unit to indoor modem in my closet

Need to change HFC NBN port location. Currently it's in the living room and i'd like to change it to my bedroom. Theres an old ADSL port thats currently in the bedroom which might help with drilling.