Find experienced local carpenters in Yatala SA

I am looking for a qualified carpenter or professional builder to inspect, repair, and remediate an outdoor timber balustrade on my balcony. Other materials other than timber are also acceptable. Current Issue: At least one horizontal timber slat has wood rot causing a major structural gap. Some sections also show signs of weathering and soft wood. Job requirement: Conduct a thorough structural safety check. Remove and replace all rotten, split, or structurally compromised timber sections with matching, durable outdoor treated timber (e.g., H3 treated pine). Re-secure all loose components, ensure strong anchoring to the sub-structure, and bring the overall barrier up to safety standards. Prime and paint all newly replaced wood. Please provide a quote (Directly accessible from outside). Thanks.

I need this freezer to fit neatly underneath my cabinet - shelf and bottom need to be cut back .

​Title: Timber Deck Cleaning & Restaining + Post & Rail Painting ​Description: Looking for an experienced tasker to clean and restain an outdoor timber deck and paint a short post-and-rail fence. ​I already have the stain (Cabot's range—previously used on this deck), so you won't need to supply the main finish. ​Scope of Work: ​Prep: Wash down the deck and fence area thoroughly to prepare the timber surfaces. ​Main Deck Area (2 Coats): ​Front section: Approx. 5m x 5m (plus ~500mm high fascia/edge) ​Side return: Approx. 5m x 200mm ​Access step ​Fence (2 Coats): Approx. 15 linear metres of post-and-rail fence. ​Application: Apply two coats of the provided Cabot's product to the deck, step, and post-and-rail fence, allowing adequate dry time between coats. ​Details & Requirements: ​Must bring your own pressure washer/cleaning equipment, brushes, rollers, and basic prep tools. ​Experience with timber deck maintenance and Cabot's products preferred. ​Please ensure clean lines and neat application around edges. ​Location: West Lakes Budget: $500 (Open to quotes based on scope)

Add extra beams to entire roof structure of approx 100m2

replace spiral balance in a timber frame single hung window. Spiral balance/ window height 880mm in height, width 1150mm.

*Tall Slim Cabinet - $40* Light wood finish. 1 drawer + 3 shelves. Great for books, storage or entryway. Pickup Adelaide.

Raise 2 small kitchen cabinets and complete cut out for range hood and flue holes.

I recently had a kitchen renovation and wasn't told that the rangehood ducting and concealment wasn't included. So I've had the ducting installed but it now needs to be concealed. The ducting + the old exhaust fan hol needs to be concealed. Would like it done in the coming 4 or 5 days if possible. The options would be a full white panel above the cupboards or a white box installed around the ducting and previous fan hole. However, the previous exhaust fan hole sits out a little bit from the front of the cupboards so any concealment will need to be put on an angle.

The bottom left corner area of the window sash has developed wood rot. So I need someone experienced in timber window repairs who can look at the damage and either: - replace the damaged section, or - replace the window sash The window sash measures approximately 84cm by 52cm. Photos attached.

Range hood is different size to the old on that was there. This has left a gap around that I want covered. Was thinking using something like pictured and paint it to match cupboards but open to suggestions.

I’m looking for some help woodworking and carrying a heavy plywood desk up the stairs. I'm wanting to have the desk width sawed 85cm narrower (cutting off the back of the legs & tabletop as indicated in images, to remove the uneven edges), potentially refinishing, and then lifting it up a narrow staircase. Technically the desk does fit. With the 85mm removed the final dimensions would be: 750mm H x 2000mm L x 665mm D, and the hallway is 810mm wide from each skirting board (though the handrail may get in the way). I believe if lifted vertically it could make it around those corners, though I’m not 100% sure as my friend and I were too weak to make a good attempt. If it turns out the desk won’t fit, I’d also be open to having both/one of the legs sawed off so that I can reconstruct somehow it situ (for additional $). It’s just a nice chunk of plywood so I want to make it work asap

There's is a small whole in the bedrooms door .

We have two problems to sort out: [1] Front pedestrian gate has expanded due to damp and so the lock is just too tight. Gate needs readjusting. [2] Need to rehang a repaired window shutter that is off a first floor window. Hinges seem fine. Can get access from inside.... Looking for someone with good woodworking experience!

Our ceiling has water stains. We don't know the cause. Looks like broken roof tile . Just wondering if some can have a look at it and fix .

Im looking for someone who can change my kitchen cabinets doors into white color.

Hanf few items and fit new shelf to wall

Retrofitting 3x popup money tills to existing wooden benches

Looking for an experienced cabinet maker or carpenter to build and install a custom joinery unit. Scope includes: * Site measure and final dimensions * Material ordering * Picking up materials * Manufacturing * Installation Materials will be paid separately. Labour budget: around $2000 (negotiable depending on experience and workmanship).

4 Timbers need to be screwed on the back (each as, just follow the instructions), and 2 vents need to be swapped around on most the inside (3 screws in each vent). All material and screws are there

I have two cabinets doors that that need to be attached as the doors have fallen off again. I recently had someone fix it but it has fallen off so I am guessing the holes on the cabinets are too wide so it’s not just simply screwing the hinges again .