Find experienced local carpenters in SA

I need someone to come to my place with their tools to cut four wooden table legs to make the table shorter in height

Wanting a floating cabinet across the crease cut please

I’m looking for some help woodworking and carrying a heavy plywood desk up the stairs. I'm wanting to have the desk width sawed 85cm narrower (cutting off the back of the legs & tabletop as indicated in images, to remove the uneven edges), potentially refinishing, and then lifting it up a narrow staircase. Technically the desk does fit. With the 85mm removed the final dimensions would be: 750mm H x 2000mm L x 665mm D, and the hallway is 810mm wide from each skirting board (though the handrail may get in the way). I believe if lifted vertically it could make it around those corners, though I’m not 100% sure as my friend and I were too weak to make a good attempt. If it turns out the desk won’t fit, I’d also be open to having both/one of the legs sawed off so that I can reconstruct somehow it situ (for additional $). It’s just a nice chunk of plywood so I want to make it work asap

There's is a small whole in the bedrooms door .

Commercial cabinetmaker required urgently for one fixed restaurant banquette/Sofa base and approximately 7-metre overhead cupboard built and installation at Marryatville. Drawings supplied. Site ready for measure.

Simple job: drill through my timber verandah beam (30 mm thick) and fit approximately 10 x M10 x 75 mm stainless eye bolts with washers and Nyloc nuts. I supply all the hardware and a one-page sheet with marked photos showing exactly where each bolt goes - one near each post, one mid-bay, all on a level line. You bring a drill, a sharp 10.5 mm bit, a spanner and a step ladder. Single-storey, flat paving, max height approx. 2.4 m.

Installation of flat pack cabinetry

We have two problems to sort out: [1] Front pedestrian gate has expanded due to damp and so the lock is just too tight. Gate needs readjusting. [2] Need to rehang a repaired window shutter that is off a first floor window. Hinges seem fine. Can get access from inside.... Looking for someone with good woodworking experience!

Qualified and experienced carpenter required to fill in a large servery hole in an internal wall in an old home. Cabinetry removal required as well. Gyprocking and insulation required. This is currently a dining room that we are converting to a bedroom.

​【Budget】 $800 AUD (Base budget. Experienced carpenters with a proven portfolio are welcome to discuss a revised quote based on workmanship and finish quality.) 【Dimensions (L-shape)】 Main Bedhead Wall: 3.3m wide Right Side Wall: 2.07m wide Height: 2.6m 【Materials Provided】 9 x Oiled Walnut Slat Panels (300cm × 64cm) 1 x Matching Walnut End Trim (3m) 1 x LED Strip Kit (4 strips + transformer) 1 x Clip-on peg shelf 【Scope of Work】 Cut panels from 3m to 2.6m using a track saw to prevent veneer damage. Precise cut-outs for 2 x double GPOs (flush finish required). Conceal low-voltage LED wiring behind panels before installation. Install panels with accurate vertical alignment and clean L-corner joint. Cut and install end trim on exposed edge (260cm). 【Requirements】 Must have professional tools (track saw, laser level, etc.). Please include photos of previous timber slat wall / feature wall projects. Careful handling of premium timber veneer materials. Clean and tidy workmanship required.

Our ceiling has water stains. We don't know the cause. Looks like broken roof tile . Just wondering if some can have a look at it and fix .

Im looking for someone who can change my kitchen cabinets doors into white color.

4 Timbers need to be screwed on the back (each as, just follow the instructions), and 2 vents need to be swapped around on most the inside (3 screws in each vent). All material and screws are there

Hello I have small job for a retired carpenter or carpenter looking for an odd job to install a u install it (already assembled) draw, shelf x 2 and cupboard into a very small pantry

I have two cabinets doors that that need to be attached as the doors have fallen off again. I recently had someone fix it but it has fallen off so I am guessing the holes on the cabinets are too wide so it’s not just simply screwing the hinges again .

I Need to install the door I will be home during the day today or tomorrow and I can help to hold the door if needed. Send your offer please

I have an L shaped cupboard door thats come off, the bottom screws have snapped into the wall I just need the door back on I'm not fussed if the screws are removed or if you just put them in next to it. As long as its functional as it gets opened and closed hundreds of times a day. Otherwise if you can just put the holes in for the new screws I can reattach it myself, I just dont have the tools I need to drill the holes or remove the screws.

Repair rotting timber as pictured in outside eaves, door of house.

Fix door hinges of kitchen cabinet

Please quote for wood rot in post and beam of verandah, also bottom of a garage door. I will have a painter finish the job. Budget flexible as I’m insure of the scope of work. Thank you!