Find a local Tasker to help you make a kitchen cabinet in NSW

I want the kitchen cabinet doors to be replaced with similar type doors. If somebody nearby Hornsby can come and have a look to give a quote, that would eb great. I am attaching some picture to give you the idea, but it may not give clear idea about the volume of work. I can buy the product but somebody needs to install it.

I need to replace the base cabinets in a kitchen like for like. 1.- One consists of 4 drawers (3 drawer front one hidden draw.) 2- A set under the sink - Two drawers. 3- A corner cupboard. The kitchen was flooded a while ago so it has to be replaced. They are just ikea flatpack cupboards. Has a stone bench top that I want to keep.

Carpenter required to adjust the kitchen cabinets to install a dishwasher.

Extend kitchen cabinets to sloping ceiling, approx 1 metre higher than current height. Doors will need to open from bottom due to ceiling slope towards front of cabinets. Looking for budget options, can purchase and provide all parts myself if that will reduce cost.

Give me your price for modern kitchen supply only. Looking for a cabinet maker or someone with the right tools to cut me cupboards and label them for flat pack delivery. This will be for a modern kitchen to be delivered (can be picked up) to Cringila. -16mm standard melamine for all internal things - outside things to be a Matt colour board (price for low cost colour - not white) - doors to be glossy (colour tbc - not white) - standard square door design (16mm is fine) - if you want supply parts as well see below: - soft close hinges - push to open bottom doors/draws - top to be manual open with the 45 deg cut on bottom of door for fingers (except above fridge) - pantry to have standard handles - no kitchen bench top

I’m looking for an experienced handyman or finish carpenter to add decorative moldings to my kitchen cabinets. I want to match the style of molding that’s already on my island cabinet (you can see it in the photos). Details: • The job involves installing similar trim on the upper and lower cabinets. • I’ll provide the photos for reference, and I’d like a clean, polished finish. I will provide the material needed.

Modify kitchen cabinet to fit a larger oven.currently height of 42 and modify to 60

Looking to modify the left row of base cabinets (see photo) to fit a dishwasher and washing machine under the benchtop. I want minimal changes to the current layout and a neat finish. Open to your input on the best final configuration before work starts. Scope Remove/adjust existing cabinets and kickboard on the left side. Create two 600 mm openings. Keep existing benchtop and overall layout. Tidy up exposed edges and panels. Appliances supplied separately (not part of this task). Please include - Photos of similar work or brief experience. - Availability and estimate for completion cost and time.

Looking to get our grey kitchen cabinets and fridge cabinet repainted/coated matte white to match the opposing cabinets.

Build the Kitchen Island Cabinet fully according to specifications.

Hi i have some ikea kitchen cabinets to be installed , the cabinets are mostly built already, just need help finishing them off and then installing to the walls

I am needing someone with the appropriate hand held saw to cut out the red section of this shelf that is under my sink. The pipes are built into the shelf so unfortunately it can’t simply be pulled it out

I currently have a whole corner of my kitchen cabinetry which has gone unused due to the current setup of the doors. I am after a cabinet maker to see if the doors can be modified to accomodate a corner. Price opening door from two standard doors. Price negotiable

- install 4 (general power outlets) gpos for the following (electrical materials included); fridge, rangehood, dishwasher, benchtop. -Remove exisiting sink and cap water. -convert copper plumbing to pvc - modify following cabinets:- 1200mm base -> 600mm oven base 1200mm base -> 600mm sink base 450mm base -> 200mm spice drawer -install cabinets on wall, level, cut in appropriate services. - install end panels, fillers, and kickboard. -afix doors and handles. - Materials to be supplied by owner or reimbursed. Items include but not limited to additional fixings, kickboard, ikea cabinets if existing cabinets poor condition (as discussed), ikea 200mm spice drawer. - View all the details of this offer: https://www.airtasker.com/offers/01K29WX0E2VP6FMM8CG581XTK0

Remove the current cabinets and bench top from the kitchen and replace with new ikea cabinets and timber bench top. All new stuff will be sourced by us. Dont need to worry about disposal. Includes 4 base cabinets (2.4m), timber bench top (3m) and 2 mounted wall cabinets. One of wall mounted cabinets holds range hood. Bench top extends over under-counter water heater. Doors and shelves removed already. Hoping to get done before 4th August.

Drill a hole in kitchen cabinetry to allow a power plug through and have it finished off with a ‘sleeve’

We need the cabinet above our fridge cut so it can be raised up to fit our new fridge underneath. See photos. The fridge space right now is 850w x 1710h x 870d (and 622d on the left side). The fridge is taller than we have room for - its dimensions are 835x1787x730mm. The fridge's depth and width are OK, it's just the height that's a problem. So this task is for you to help us out. We need the cabinet taken off the wall to have some height cut from it, then mounted again 80mm higher up. To try and be ultra clear - new fridge is 1787mm high but the current fridge space is only 1710mm high. So there is an 80mm difference. We need that extra height to fit the fridge, which requires cutting the cabinets shorter. There’s 45mm of space to move it up, so the cabinets would be cut shorter by 35mm and moved up 45mm.

Need someone to take a look at this hettich hinged door. I’ve taken it off, it doesn’t close fully and is fouling despite adjusting the hinge screws.

I would like my kitchen cabinet fix as it loose small screws

Hello, my revolving 360 Lazy Susan corner kitchen cabinet is no longer turning correctly. The metal in the mechanism at the bottom looks a bit bent from use over time and the plastic in the mechanism sometimes pops out. This results in it not spinning around smoothly and dragging against the inside of the cabinet or sometimes not revolving at all. The two cabinet doors are attached to the revolving cabinet. I think the mechanism will need to be replaced (if you recognise the model) or perhaps the whole rotating cabinet may need to be replaced.