Find experienced local carpenters in NSW

Need someone to replace and adjust hinges on two full height cabinet doors at a clients place in Surry Hills. Assume 8 hinges per door. Client says when doors where previously installed the doors opened and shut nicely, but over time they began to sag and are now hard to close. Unfortunately do not have a photo of the hinges themselves.

Want to create a custom entertainment unit… specs and design / materials TBC. Approx 3m wide x 600 deep x 300mm high mounted on wall…

I need some joinery repairs done as follows: 1) Joinery panel 2.1m X 0.6m came off the ceiling, needs to be re-glued securely as it's a heavy panel. 2) Joinery door of cupboards below BBQ on terrace came off due to loose/corroding hinge &/or screw holes 3) Vertical battons glued on to joinery panel at entry have come loose, needs to be re-glued with clear glue. I have attached photos of each of the three areas.

We have a small storage space with the following dimensions: Height – 241cm, Depth – 117cm, and Width – 98.5cm. We're looking to convert this area into a compact study nook based on a design we’ve already prepared. We'd love someone to help bring this to life.

Strip out shelves and desk from wardrobe. The full height joinery panel on the right will need to be retained, so careful removal would be appreciated. Shelves and desk are glued, but also screw fixed to the wall and RHS joinery panel. Carpet is being removed so no need to be precious with that.

Cut out back panel to gain access to a tap in base unit

Hi guys, I need 6 tasks done in a property that is mainly joinery work that align with photos to come; - Picture 1- I have new joinery doors for a kitchen that I just need installed. New doors will need hinges cut in and will also need new handles installed - Picture 2- there’s a piece of timber flashing that needs to be fixed above the kitchen joinery - Picture 3- there’s a piece of plastic flashing that needs to be cut and glued as shown in the picture. - Picture 4 and 5- there’s 2 handles that need to be fixed to the sliding door into the bathroom in the locations shown. Please make sure the bogged areas from the previous holes are missed on both sides of the door when doing this. - Picture 6- there’s a piece of melamine board that needs a jigsaw to cut as shown in the picture and then just screwed down into the board below All equipment supplied. Just need a joiner and your tools… Cheers, Mike

Someone to come and quote on building 2 x black cabinet ends pieces like the one in the pictures below - client is installing aircon units inside them and basically need to cover them over - will need to provide guidance on cost.

Need joinery fixed: - new doors for a tv cabinet - replacing the existing hinge And insert a bar fridge into cabinetry Please contact me for further details Need a quote (budget here is not indicative) We also have a much bigger job which is a new custom made outdoor kitchen but we want to see if this job can be done well first. Thanks

Corner cupboard not closing in lower corner cupboard in kitchen.

Need cabinetry installer to assist me with installing a bunnings kitchen. 3 cupboards and 6 sets of drawers. It's a kitchen island and includes an installation of a benchtop (no cuts required). Photos attached to this post.

I need someone to help me adjust a fridge cove to ensure that the fridge will fit properly. Pictures attached.

I would like a custom desk built to fit this work space under my stairs . Would like to use oak wood . The desk should have storage draws and possibly another part for storage . Open to design ideas . The length is 187 and width is 60cm. Would n ed you to do a home visit to discuss the job and measure up properly if interested.

Looking for someone who can make me a banquette seat base and table

Need assistance to dismantle the old internal joinery of a wardrobe and install new IKEA shelves.

Fit out workstation area in office See attached photo for dimension and sizing

Hi - we need to get joinery removed from next to a bed (shelves and short cupboards - see picture below) and a desk removed from a bedroom (dont have a picture but its around 3 metres, simple desk, no shelves or cuboards)

Measure current cabinets and replace with new ones in black

Seeking a skilled joiner or carpenter to repair and secure the wooden stick base of a queen bed. The job requires ensuring the base is sturdy, aligned, and durable. You will need to bring your own tools for the task. Kindly provide your quote and availability. Thank you!

The hinge on my bathroom cupboard door has come loose. It’s been repaired before but has come loose again. The door is quite heavy and the angle makes it a bit tricky to hinge and repair.