Find experienced local carpenters in North West Melbourne

A wooden frame surround, to hide existing iron frame in fireplace. Not a huge budget available. The wood will not be painted, so something nice but not too expensive required. Plan of what needed in the photos.

So the cabinet door under the sink in my washroom needs to be fixed. I have attached the relevant pictures. Please check and let me know if you have any questions

Hi Need to assemble a sauna flat pack. Installation requires 2 people and should take roughly one afternoon overall. Sauna assembly itself is estimated around 45–60 minutes. Difficulty level is easy and a setup video is included. Also required on the same job: Install door frame and hang door. Please make sure all tools required for door install are brought to site before attending.

We have bought a new 900mm freestanding oven, and the existing space is only 800mm. We need to increase the opening by 50mm each side to allow for the new oven to fit

We recently had new face boards put on to wrap around the outside of a deck adjustment. The person who did it said they could not get the bottom board any more flush to the ground due to the floor concrete level being very uneven which it is (higher at each end and dips lower in the middle). However the gap is quite large and more obvious now we have painted the wood so we want someone who is able to do a better job and cut the wood more in line with the ground to leave a smaller gap. We have two spare boards of wood to use for the job, want it done only removing the bottom board not the entire thing.

As part of a bathroom renovation I'd like a Carpenter to Prepare the floor so its ready for following trades including the shower fall. Install niche. Size to be confirmed but around 750mm wide 340mm height. Plane timber around window so its flush with wall stud. The room is around 1.9m x 1.8m. The house is on stumps. If anything else is needed doing i'm happy to discuss. I've attached photos and that is how the room will look when you start. I've put $10 only to post. If you could put in an offer that reflects what you think it will be that would be much appreciated.

Need to build 2 cabinets for the below spaces - Above the Fridge - Below a cooking table. Photos are provided for these spaces. Please provide me your best quote.

Need someone that can cut 2 holes in some laundry cabinets. 1 needs will be for electric cables and the other for our washing machine cold/hot water hoses to go through

Need a small timber box/frame built around my outdoor tap and water meter as I’m raising the garden bed height around it. Needs to: * Allow access to the tap/meter * Hold back soil * Be suitable for outdoor use * Look neat and tidy Please quote including materials and labour.

Sand and stain my decks 5mx5m + a step & 1800x4m Also supply stain

Need one skirting patched up and another fully replaced

Create a Catholic altar like reference picture. A wooden deep frame with cross inside. Floating shelves for statues and bible. Looking forward to ideas. Need a simple and clean setup. Probably back illumination on the frame. Illumination may have to be battery operated as there is no power point close to the altar space.

Remove approx 200mm from a 600mm x 2400mm timber panel to use as a benchtop

Need to box out an area in a warehouse office roof. The area is 1000mm x 1000mm x 1500mm. The ceiling is plastered with clear access to the roof. On top of the office is chipboard. Timber for the job is supplied. Need the roof cutout, boxing made up and installed. Plastering isn’t part of this task.

Im after this piece of wood to be sanded, planed flat ready to be made into a table top

Hi, I have two small carpentry repairs at home: 1. One stair baluster has come loose at the bottom and can be lifted off — needs re-securing. 2. Two doors cannot latch properly and needs adjustment. Could you provide a quote or availability to fix both?

Need a timber border to be added around a grave, I will attach a couple of photos for reference. I believe 4 pieces of timber is required. Approx size below. 2x1.2m 2x2.4m

This task is to pressure wash and decontaminate a deck installed last year and apply two coats of stain to deck after cleaned and dried. This job will have to be carried out over three days. Day one clean deck Day two first coat Day three second coat Care taken to not coat rock work, brick work or concreting when applying stain Area approximately 50m2 All furniture and loose debris will Be removed prior to start day Stain and cleaner will be supplied

I need a qualified cabinet maker or handyman with cabinetry experience to come out and adjust the cabinets around my laundry washing machine space. The current cabinets are slightly uneven/misaligned, and I’m unable to slide the washing machine into the space. Task details: • Adjust/straighten existing cabinets so they sit flush and aligned • Ensure the washing machine space is the correct width and clearances • No major rebuild required—just adjustments to allow the machine to fit properly • Bring any tools needed for small cabinetry fixes (e.g., hinges, screws, levelling tools)

Description: I need a welder to permanently attach 2 threaded bulkheads to a large stainless steel pot. The silicon O-rings aren't providing an adequate seal, so I want them welded in place. Details: Material: Stainless steel pot Job: Weld 2 bulkheads (there's already 1 existing bulkhead on the lid - see first photo) Locations: First bulkhead: On the lid (flat surface) - will be the 2nd bulkhead on the lid Second bulkhead: On the side of the pot (curved surface) The pot will have 3 bulkheads total when finished - only 2 need welding. Looking for someone experienced with stainless steel welding who can ensure a clean, watertight seal.