Find experienced local carpenters in NSW

I'd like this cupboard reconfigured so the hanging rail is removed (it's too narrow to accommodate hangers!!) and the shelves are moved to the top. No shelves at the bottom. Our letterbox has also fallen off the fence and needs fixing back on.

Have a kitchen bench top that has cracked. Need to have it replaced with a new cooktop and oven

We have a small circular cut out in the back of some joinery to feed cables and we need to increase the hole slightly so we can fit a hand/arm in. Probably an extra few cm each side so a hand can reach in.

I’m looking for supply and install of office study desk and cabinetry (fixed and wall mounted). The study nook is approximately 1.5m x 3m. Photos are attached (with the orange chair). If you can dispose the existing desk that would be ideal, otherwise I’m just after a quote to get this supplied and fitted. Example photos attached to give an idea of what I’m after.

Connect washer/dryer to waste water pipe using hose connector kit. I have purchased the part already so this simply needs to be connected and machine pushed back into space

Looking for a joiner/carpenter to build shelves in pantry - as pictured (blue pen) - ideally if these shelves can be adjustable height depending on what goes in them - 1 middle wall to split and maybe 5 shelves? H-192cm W-45cm D-57cm

Need 2 living room units from floor to ceiling, first room architrave to architrave, second room fill out void. No rush but most likely work to be done only on the weekend.

Remove joinery from wall and dispose of material

Joiner, Cabinet and flatpack installer - kitchen Kensington, New South Wales 📍 Location: Kensington, NSW 🔨 Job: Kitchen Joinery – Door & Panel Installation + Minor Carcass Works We are looking for an experienced kitchen installer to refit all doors and panels on existing kitchen joinery, plus carry out a couple of carcass modifications as detailed below. --- SCOPE OF WORK 1. Measure Up (Stage 1) • Visit the property to complete a full measure up of all existing kitchen doors and panels so that we can finalise our order. 2. Door & Panel Installation (Stage 2) • Supply of doors and panels is by us — installer is responsible for installation only. • Replace ALL existing kitchen cabinet doors and panels across the full kitchen including island with new supplied doors/panels. 3. Carcass Modifications (as per architectural drawings) Section A-A (Cooktop/Oven Wall): • Remove the two existing drawer carcasses and fronts either side of the current 680mm oven opening. • Modify the opening to accommodate a new 900mm freestanding cooktop and oven.( we can supply new carcasses) Section B-B (Fridge Wall): • Remove existing upper cabinets in the fridge zone (highlighted in drawings). • Supply and install a filler panel to suit the new fridge opening. • Fridge dimensions: 2134mm (H) x 1064mm (W). Looking to complete this task in july but will need someone to come and measure up soon. Lots of additional joinery work at this property for the right person including; 3 bathrooms - joinery lots of new wardrobe joinery throughout

I have two tasks I need done: The first is the bathroom sink: when I unblocked it I noticed that it’s leaking and it seems to be from wear and tear. May need to be sealed. Also have a broken hinge on a kitchen cabinet. This might be able to be fixed but may need to replace hinge also

Modify existing timber structure for espresso bar and kitchen. Must have experience in this area either as a carpenter or/ joiner or handyman. Knowledge of how to locate and safely navigate around electrical power points and wiring. Professional cutting and finishing tools including dust extraction tools as you are working in a trading cafe. Please quote hourly rate, then an estimate for completion of job once photos are uploaded.

📍 Location: Kensington, NSW 🔨 Job: Kitchen Joinery – Door & Panel Installation + Minor Carcass Works We are looking for an experienced kitchen installer to refit all doors and panels on existing kitchen joinery, plus carry out a couple of carcass modifications as detailed below. --- SCOPE OF WORK 1. Measure Up (Stage 1) • Visit the property to complete a full measure up of all existing kitchen doors and panels so that we can finalise our order. 2. Door & Panel Installation (Stage 2) • Supply of doors and panels is by us — installer is responsible for installation only. • Replace ALL existing kitchen cabinet doors and panels across the full kitchen including island with new supplied doors/panels. 3. Carcass Modifications (as per architectural drawings) Section A-A (Cooktop/Oven Wall): • Remove the two existing drawer carcasses and fronts either side of the current 680mm oven opening. • Modify the opening to accommodate a new 900mm freestanding cooktop and oven.( we can supply new carcasses) Section B-B (Fridge Wall): • Remove existing upper cabinets in the fridge zone (highlighted in drawings). • Supply and install a filler panel to suit the new fridge opening. • Fridge dimensions: 2134mm (H) x 1064mm (W). Looking to complete this task in july but will need someone to come and measure up soon. Lots of additional joinery work at this property for the right person including; 3 bathrooms - joinery lots of new wardrobe joinery throughout

Frame / set wardrobe with woodgrain MDF Frame below cabinet bedroom wall with woodgrain MDF Trim edges Remove and dispose of waste (current veneer = bendy ply) Quote for labour only. Product example: https://trademaster.au/products/antique-oak-grain-mr-mdf-16mm-x-3000x1200mm?pr_prod_strat=e5_desc&pr_rec_id=da0f5b826&pr_rec_pid=7791517564980&pr_ref_pid=7761816780852&pr_seq=uniform

Need a Joiner for in the factory building cupboards, building doors

I need to 2 timber vanities cut down No top on them. I need this done asap I need the 2 side cuts to be clean and perfect as these will be visible Please respond with availability and cost They can be delivered to you

Kitchens wardrobes alfresco vanity installation

Need to build a cabinet build as per the picture and fit into the space as per picture. Should be in black please.. The cavity dimensions recap: • Width: ~600mm • Height: 330mm • Depth: ~500mm

Installing cupboards, kitchen, wardrobe, kicks, doors

We are looking for someone to assist in our Hornsby workshop to assemble custom timber projects. We need someone with experience working with timber and operating workshop machinery. If you can interpret plans and instructions, dress & shaping timber and assemble products to time and specification, we'd love to try you out.

Removal of kitchen drawers and relocated to second photo in preparation of a dishwasher installation