Find skilled builders in NSW

A post supporting pergola has wet rot and polycarbonate roof needs replacement and waterproofing to prevent future damage.

Timber posts of a pergola are rotted at the bottom. Another picture is showing the pergola top.

Looking for a help to: 1. Removed old wood pergola 3m x 1.6m (please see picture) 2. Install and bolt new aluminum pergola 3m x 3m (please see picture). Located in Lane Cove, postcode 2066. Thank you!

Hi, I'm looking for someone to clean and reseal my driveway and pathway. The total area is approximately 60-70 square metres. Please let me know if you're available and could provide a quote. Thank you!

Hello, I need to replace old corrugated sheets of my pergola. Remove the old fasteners and panels, check the framing for proper slope and stability, and secure new corrugated sheets (polycarbonate sheets)

Caringbah Put shed together from Bunnings 2mx3m And screw into 6 concrete blocks. Must have own tools

There is an approx 2.5m by 2m section of a driveway that is cracked and become a trip hazard. I need a concreter to remove the broken section and lay more concrete.

The garden shed is a skillion roof model - dimensions are 3M (L) x 1.5 (W). Build will be on grass and garden base not concrete slab and shed will have internal flooring as per easyshed kit floors.

We have what appears to be a blocked sewer line at the bottom of our driveway. Water/sewage is backing up from the drain/inspection point during use. Looking for a licensed plumber to: * Diagnose the blockage. * Clear the sewer line using appropriate equipment (drain snake/auger or jetter if required). * Test that the line is flowing correctly before leaving. * If possible, run a CCTV camera afterwards to identify the cause (please advise if this is an additional cost). Please bring all necessary equipment and include your availability. Photos attached.

I purchased an easyshed 2.2mx 1.5m skillion and I managed the assemble all the panels and roof with my tools available. Need help to join the panels and roof to make it a shed. Please refer to the photos. Job shouldn't take more than 1 hrs however it may need 2 people to do it.

Assemble 2.25m x 1.5m Skillion Roof Shed on concrete slab. Brackets for securing the shed on the slab are provided in the package.

Replace colorbond panel to a gate, use removed panel in side fence opening where new driveway will go, install two new posts and adjust fence opening

Install an easy shed in belrose.

Wheel barrow loads of wet concrete from concrete truck 5m and dump on driveway Approx 20 loads Less than an hour 9:30am

Rebooking task between jacob and Aaron

Looking for someone experienced. Need new drain stored. Must have experience with this.

Assembly of: 2.25m x 0.78m EasyShed Bike Shed https://easyshed.com.au/products/garden-bike-shed-2-25m-w-x-0-78m-d-classic - assemble onto pavers (slightly inclined but flat surface) See photos - No need to anchor into pavers - Will need your own tools (eg power drill/driver and potentially a pop-rivet gun, as doing this with a manual screwdriver is nearly impossible)

We need some assistance demolishing the final bits of our commercial fit out. This includes the removal of floating ceiling metal framework (tiles & lights already removed), grinding down of bolts on concrete floor, removal of floating float (half finished already), removal of mirrors (not needing to be preserved) and a couple more similar tasks.

Driveway is build couple of years back but I require Resealing of it with pebbles concrete finish. Additionally, I also need to complete the garage floor coating. Garage area is 5.5 x 5 meters and drive way is 5.5 x 9 meters.

I need a slab with single pier laid for a 5000L plunge pool. Must be completely level. Pier: 300mm diameter x 1.5M deep Slab: 2.5m diameter x 1500mm deep Cage for pier is already in place. Need 1 layer of SL82 steel mesh for slab supplied and installed prior to pouring. 1.3m side access available Will need 2 visits. 1. Install mesh prior to CDC inspection 2. Pour concrete