Find professional window and door services in Lyndhurst VIC

I had Vendline clotheslines installed a few months ago, but some of the existing screws are starting to pull out of the wall anchors. The pre-drilled holes in the metal mounting plates don’t line up with the wall studs, so I need a couple of screws drilled directly through the metal plates where the studs are located, to give the clotheslines extra support

Our screen door leading to backyard is always jammed and cannot open properly. We have tried to clean and oil but doesn't help.

Looking for an experienced renderer to apply acrylic render to specific sections of an outdoor feature wall (HardieFlex cladding). Photos and measurement drawings are uploaded. Areas to Render (approx. 7 m²): Requirements: • Acrylic render suitable for HardieFlex • Two‑coat system (base + skim) • All masking and protection included • Painting not required (I will paint later) Access & Timing:: Outdoor job, easy access. All days except Sunday.

Let me know if you cando it thanks

Need to hang a door old one is broken got new door and new lock

I would like to get my Garage Roller door serviced , And get a universal remote (already purchased) Programmed if possible?

I need the springs of my garage’s door replaced as 1 of them is broken. Can you please provide an estimated cost?

Hi need plaster and door repair: - 4 small patches to be fixed below - one door to be put back on hinges and small repair on door - we mounted a tv that has been taken down, so there two round roles to be plaster filled, and also two small white screws which need to be removed and also plastered over.

I bought garage door WiFi mobile opener device, need to install

one door and a wardrobe door has got small damage area, see photos, need its repairment and painting before 22 April anytime suitable to you.

Internal garage door came off, need to fix that, see attached photos.

B&D PanelPro garage roller door motor in a double car garage that is not functioning proplerly and needs fixed Issue: - Door starts opening but only lifts 2–4 inches from the ground - Makes loud vibrating / rattling noise from the chain rail (I think, not sure) - Then gets stuck and stops - Same behaviour when attempting to reset travel limits What I’ve checked: - Door operates smoothly and easily in manual mode (not heavy) - No visible obstruction in tracks (that I could see) What I need: - diagnosis and resolution for jamming issue - oiling/grease & service of the setup Property details: Double car garage roller door Easy access Located in Lyndhurst, VIC

Scope of work: Supply all materials required for works. Cut tiles to allow bottom plate of stud wall to bolt to concrete Build a stud wall with 90 x35mm pine to enclose the study area. Supply 1 x 820 x 2040 door and jamb Insulate the wall and then clad in plaster sheets both sides Tape the joints and fill with plaster compound and fill gaps and allow to dry Supply new cornice to match existing and install Sand smooth the plaster joints and gaps Install the door jamb and hang the new door and install a new handle. Supply new skirting and install. Supply paint and primer and paint the walls, ceiling, cornice and door and jambs

Our double front door is shown in the pics. The door on the right has dropped a bit and needs readjusting. See pics showing small gap on the top. Approx measurements: Top gap right side door to frame approx 1cm, between two doors on top- gap approx 3-4mm and between doors at bottom - approx a cm. Near hinges, narrower at the bottom and wider at the top.

I’m planing go convert my single garage to a studio with entrance. The garage door needs to be removed and made into an entry with door. Pictures are attached of my garage and of how want the entrance to look like. The size of garage door is 250 cm x 210 cm

Please quote for adding two doors with mouldings/trim opening in the middle with no hinges or knobs to the under-stairs wall. Attached is the picture with the dimensions and another picture shows the sample door finish but size needs to be suited to the available space evenly.

Looking for someone to resize (reduce height) of an aluminium sliding flyscreen door.

Accidentally the shower panel door came off and lower hinge is broken. Need someone who can get this sorted.

In the master bedroom, there is no door on the toilet. I want a separation between toilet and walk-in robe. I'm after a glass door/partition, a sliding one, preferably barn-door style. Please see the pictures. Dimensions of this cut out is: 239 cm high 77 cm wide

Side entrance door frame coming off the wall, need this fixed.