Find professional window and door services in Eltham VIC

Need someone to install a heavy duty rubber or silicone door sweep under my basement door. The gap is letting in alot of leaves and lizards and it needs to be fixed. It's also on an angle so that needs to be considered

My bathroom sliding door is broken. Need someone look into it.

I need someone to remove this old security door. We have lost the key for it so it’s not easy to remove.

Need someone to install a heavy duty rubber or silicone door sweep under my basement door. The gap is letting in alot of leaves and lizards and it needs to be fixed. It's also on an angle so that needs to be considered.

Old window with 2 layers of paint needs stripping back to timber

Fix 4 door knobs and large roller door may need rollers replaced

Requesting someone to install a Ring doorbell on a rendered concrete wall

Hi, need a shower door supplying and fitting

Adjust spring in garage door

Sliding door doesn't close all the way, I think it's the runners, if they could be adjusted, heightened, the door will close all the way.

Kitchen cabinet door, beneath sink, needs realignment of the hinge. Doors don’t close properly.

Hi there, I need help removing two large metal beams/brackets that were originally part of a garage door system. They’re currently fixed to the wall and floor of my studio/garage. What needs doing: • Remove, and then dispose of two metal beams/brackets attached vertically to the wall, • Both beam have bolts into the concrete floor that I unable to loosen with any tools I have (e.g. adjustable spanner) • The beams also appear firmly secured to the wall • I don’t have the tools to remove these safely. Possible approaches (your call): • Cutting the floor bolt using an angle grinder or reciprocating saw. • Removing or cutting any wall fasteners. • Gently prying the beams off the wall once the fixings are released. • Ensuring the wall is left safe and clear (minor cosmetic damage is fine - this wall will be covered). JOB: • Must bring own tools (grinder, reciprocating saw, metal blades, socket set, pry bar, etc.). • Ideally someone who can also dispose of the metal beams once removed.

Replace fly screens on two wooden sliding doors with stronger mesh (as we have a cat). One door only requires the bottom section to be replaced, approximately 1040mm x 760mm. The other door requires both top and bottom replaced, so roughly 1040mm x 760mm and 1040mm x 1220mm (or 1040mm x 2000mm if top and bottom can be done together).

Replace damaged door jamb and architeaves Jamb and materials on site

Replace a window winder, the screw on the old one is stuck. I have a replacement one.

I am looking for someone to install 2 x Ikea Skytta Sliding door system in two of my bedrooms. Picture of the two rooms and the plan as per pictures attached. Installation video as per below: https://www.youtube.com/watch?v=uDYRh-_KB-8 Ideally looking for someone to come on Thursday 18/09 to my property in Eltham. The rail will need to be cut to length, and there is skirting and architrave to cut into to make it fit against the wall. Thank you.

The door is rotten due to rain damage over years. I don’t want to buy a new one and prefer to repair it if possible. Once repaired add rain deflectors to the door. I am looking for someone honest that can tell me if they can get it done properly or if it is not repairable at all. Alternatively, please tell me if it is not repairable whats the cost for a new door to be installed? I am happy to discuss price. Thank you - Due date: Flexible

Need a door installed. Door is brand new therefore needs handles, hinges installed (which we have). It is replacing an interior door which was narrower, therefore the frame (door stopper) needs to be trimmed or replaced to match the new thicker door. Besides the thickness, door should match frame. Worst case some trimming on bottom edge if necessary. Door is made of timber & glass. Door is an exterior door so not light/hollow like most interior doors. If done on weekends I can assist with lifting etc if needed.

I need an external door rehung so that it opens outwards instead of inwards. The hinges will need to be repositioned, and the latch and strike plate adjusted so the door lines up securely and locks properly. The door and hardware are already here, it just needs to be re-fitted. It may involve a little chiselling or re-cutting to make sure everything lines up neatly. I’d like the job finished to a good standard so the door opens, closes, and locks smoothly.

Two closet doors require hanging, rollers need to be taken off and re-fixed properly on one door aluminium guide will need to be installed and chiseled in.