Find local power point installers in QLD

New power point installed along with new wiring etc. in living room for new reclining lounge chair, and also an outside power point to be replaced as old one is currently damaged.

I need a licensed electric to install a new power point next to the toilet in my ensuite bathroom - this is for a new toilet seat that requires a 220-240V power outlet. Not sure if it matters but there are other existing power outlets in the ensuite already, just not one next to the toilet. I have the outlet bought and ready to go. Addition wiring etc. will need to be supplied. Thank you!

Hi I am getting new cabinets and new power points moved down below cabinetry . Also need a few other power point moved

Just to replace a power point that is damaged Before 12 noon please

Display monitor to be installed. Power point needs to be installed behind it. We have the screen but not the wall bracket.

Need to install 2 15amp power points at resturant.

Hi, I’m looking for a licensed electrician to help set up my home so some power points work when there is a power outage. I have a solar system with a FoxESS 10kW inverter and a 43kWh battery. At the moment only lights and fans work on battery.

Replace power points of bedroom and living room (8 provided by me) move internet wiring to another section of living room. Bathroom: Disconnect the bathrrom power points (2) before or on 6th Feb. Come and Rough in once demolition happens on 10th February for power point (2) and three in on light/fan/exhaust, two led down lights. Once sheets and tiles are in, install the products. Move the security camera wiring in the wall in the hallway. This can be done at the time of bathroom rough in.

I need 4 power points installed indoor. One beside the cooking range for an air fryer, one at the front of bench top, one in living room and one in bed room. Also need a switch replaced. Photos attached.

Need two light witches and fan switches redone into a wall. Two power points installed and two removed. Would be an hours work tops and items supplied.

Need a power point moved in laundry to below bench. Steel frame house

Seeking electrician to replace about 8 dbl power points with supplied new dbl points with usb and install of 3 external power points. Review of board for support of separation of power to sheds.

A licensed electrician required to add power point as marked in the photo.

I need to 15 amp power point nstalled for a new spa I got for Christmas. It will be outside, on the back of the house i think

Kitchen Powerpoint not working

Need someone to bring the bulb (buy it) and install into lighting fixture. One bulb needs replacing, all others are working. Must have a tall ladder as ceiling is 10ft tall. Bulb specifications are pictured. Fix 2 Ethernet wall plugs (the switch has fallen behind accidentally after pushing it in too hard). Switches work perfectly fine - it’s just the cable has fallen into wall 2-4cm.

Looking for a licensed electrician to complete a few small electrical jobs: Reposition one existing light switch in the garage Move the existing power point for a fridge higher up the wall (inside the house) Install two additional new power points (inside the house) All areas have easy access. Power points and switch plates are provided — just need installation only. Please include in your offer: Your license details Estimated time to complete the job Availability over the next week Located in Nambour Budget: Around $400 (flexible depending on job details)

I need a double power point installed in my dining room wall.

NBN cable is in the roof of my yoga studio and nerds to be relocated so the ntd and modem can be plugged in near a power point. It is quite long so allows some leeway. Hopefully install a cable wall plate so it’s tidy?

I’m replacing my existing hard-wired oven (20A) with a new oven that has a 10A plug. The current setup is a hard-wired 20A oven circuit (with existing cabling in place). I need a licensed electrician to: Disconnect the existing hard-wired oven connection. Install a standard 10A single power point (or double) (surface-mounted or flush, depending on what suits). Replace the 20A circuit breaker at the electrical switchboard with a 10A breaker to suit the new outlet. Test the circuit for safety and compliance (RCD, earthing, etc.) Notes: The existing cabling and circuit are already in place — just need conversion to a socket outlet. The new oven is 10A with a standard plug (comes fitted). Please bring all required parts (10A socket, 10A breaker, etc.) and include them in your quote. Location: Robina When: Flexible — ideally within the next week. Requirements: Must be a licensed electrician (please include licence number in your offer).