Find local power point installers in Logan Beaudesert

Require 2 double plug power points to be installed

Need 3 fans to be replace with installation of 3 chandelier light in kitchen area, wired already inside the roof with one power point installation in the kitchen area

Powerpoint #1 under sink - cords do not sit flush when plugged in. Keeps protruding out. Must be damaged Power point #2 in room - is just loose, needs to be refixed

Licensed electrician needed in Marsden (house). All fittings are already purchased, so this is install labour only (plus any sundries). 1. Downlights: replace the old light fittings with 6 x CLICK CCT LED downlights (4 x 90mm and 2 x 72mm cut-outs). 2. Switches and power points: change approx. 8-10 single switches and power points to doubles. 3. Bathroom: remove the existing light and install a CLICK 3-in-1 bathroom heater / exhaust fan / LED light (model CK4U, 4 x 275W heat lamps). Needs the ceiling cut-out, fan venting, the correct switch for the unit and any circuit work the heater needs. Must be a licensed electrician and provide a certificate of testing / compliance on completion. Please quote a total fixed price including GST. Photos available on request.

I need two outdoor GPOs installed , an outdoor ceiling light installed (I have the light) and install a Unifi Gate Hub which will need low voltage wire. I can supply an install guide and can help with the install of the hub/wiring guide, I just need the physical/electrical side done so you don't need to know anything about the hub to install it. You will need to supply the two outdoor GPOs and the low voltage / ethernet wiring to install the hub. The hub will be in the same room as the switch, so will need less than 10m of ethernet/low voltage wiring.

Need 4 power points and 5 lights outdoor area. Open for quotes

PowerPoint needs to be reconnected to the wall instead

1x single power point converted to a double power point and a new double power point added

Power point need to be fix in Underwood

I need a 15 amp power point outside for pool heater, and also supply and fit smoke alarms in the house to comply with legislation. Need licensed electrician.

Looking for a licensed electrician to do the following: * Install 2 new double power points in the living room * Install 1 new double power point in the kitchen * Change 3 existing single power point to a double in the bedroom * Install/replace 1 ceiling fan at an existing fan location (fan supplied) Budget around $500 for the whole job. Please let me know if you can do everything for around this price.

Remove these power plugs and a light switch and replace with new ones which I already have.

Looking for a licensed electrician to install a single GPO (power point) under our internal staircase in Waterford, QLD. NBN is upgrading our home to fibre, and the internal NBN connection box will be installed on the wall under the stairs. There is currently no power point nearby, so we need one installed to power the NBN equipment. The location is easily accessible under the stairs (see photo). We’d ideally like the power point installed on the wall adjacent to where the NBN box will be mounted.

One power point in bedroom and one in kitchen area

3 power points for security camera . 1 power point at patio 2 at inside home for recliner chair . And 1 light point inside home for a photo frame . Also two lights at the front of the house . I can provide the photos of the plug points i have already at home . Please qive me a quote

Lounge room - New installation, remove old light Dining room - New / Replace Entrance way - Replace Hallway - Replace Toilet - Replace

I need the existing power point moved slightly to the left, and a new one put in about a metre below it.

I just need a power point installed for my new oven, or rewire the new oven into the current hardwired setup. The stove top is running out of the same box and i need to keep this the same for the stove top.

The scope is as per below: 1) Install 5x feature lights on external boundary wall (12VDC). Pre wiring already done 2) Install 4x step lights (12VDC). Pre wiring already done. For 1&2 existing Jb to be repalced with larger one to house driver and tie in to existing 240vac JB. 3) Install 3 x feature lights to house on existing JB. 4) Install outdoor power point in front of house. Pre wiring already done needs to be terminated at both ends. Power point to be supplied. 5) Install outdoor power point in backyard on garden bed retaining wall of house. Pre wiring not done. Conduit exists to run cable and terminate at both ends. Power point to be supplied.

Install gpo and tv point behind tv unit