Book a trusted oven repair and installation expert in WA

Kleenmaid Scala oven door hinge has come apart and needs repair.

Asko oven. Turn on, set the temperature but it doesn't rise.

Hi, The oven turns on but doesn’t heat up, fuse behind the oven might be blown but not sure. Let me know if you can assist. I can assist with pulling the oven out for access.

Installing a pendant shade in the dining room

Remove old oven and install new dual fuel oven. Dispose of old oven. Installer must hold relevant qualifications and lodge relevant has installation paperwork.

I have a Delonghi oven - It is gas stop and electric oven. The oven is not heating up. Can you help?

I have a Westinghouse oven (model WVEP6158) where one of the small push buttons has broken off. The button needs to be replaced. If an exact replacement cannot be sourced, I am open to replacing the matching buttons with alternatives that closely match the originals in colour, size and appearance. Located in Coogee, WA. I'd like the work completed within the next week. Please provide a fixed-price quote including labour, parts and GST.

Windows, Blinds, Extractor Fans, Oven, Showers

Freestanding oven WFEap9717 westinghouse

Install a second hand oven not sure if it’s gas or electric

Hello think some of the wiring in my oven has been knocked and it’s no longer going into oven mode or heating up

Hot plates are working but not oven.

Require 600mm electric wall oven to be hardwired and installed by electrician. Old oven to be disconnected and new oven connected.

I have Indian clay oven ( tandoor ) on the top part on it ring is rustic , it”s new oven bought from overseas . Sharing picture

Job1- Left oven to the base average weight 180 to 200 kg diameter 90x 100cm, Distance from Oven to Base about 2 meters. Job2- left the bricks to tip per picture4

The spring that holds the door of the under bench oven is broken and need to repair it

I would like to change my no longer working gas oven to an electric oven, installer who is electrician said a plumber needs to disconnect the old oven.

I need an experienced solid plasterer/rendering professional to repair the outside face of an existing oven recess in my kitchen. The inside of the recess is NOT being plastered and will remain exposed brick. The work is to repair the damaged areas around the opening, including the sides and top, build up/level the surface where required, and finish it flush with the existing wall and smooth/ready for painting. This is an older brick/masonry wall, so I’m specifically looking for someone experienced with solid plaster/render repairs over brick, rather than someone who mainly does plasterboard. Materials to be included in the price. Photos attached. The job is ready to be completed now. Please provide a quote and, ideally, examples of similar brick/masonry plaster repair work you’ve completed.

Kitchen Renovation – Brick Cut-Out Required for Oven Tower I am currently having a kitchen renovation completed and we are looking to install an oven tower. The oven tower will include drawers underneath the oven, with a microwave space above it, as marked in the attached photo. To allow the oven tower to be installed, some brickwork will need to be cut out above and below the existing oven space. It is highly likely that a lintel will also be required to support the weight of the brickwork above. The kitchen company is able to supply and fit the oven tower, but they are unable to cut out or remove the required brickwork. We are arranging for an electrician to remove the oven, but we are looking for someone who can assist with: Cutting out/removing the required brickwork; Installing or allowing for a lintel if required; Disposing of the removed bricks/rubble; and Preparing the space for the oven tower installation. The cut-out can be no higher than 1900mm from the floor, and the width will need to match the width of the oven tower/frame. Ideally, we would like this completed as soon as possible from Thursday 6 August, as the kitchen renovation is expected to commence from Wednesday 12 August. I am based in Palmyra and would be happy for you to come and inspect the job beforehand if that helps.

Seeking licenced gasfitter to disconnect gas from old Andi 60cm freestanding oven and connect gas to new Westinghouse 60cm freestanding oven (model no. WFE616DSC) - hopefully a quick job.