Find a local Tasker to help you make a kitchen cabinet in NSW

I need a cabinet maker/carpenter to modify an existing kitchen cabinet to fit a standard 60cm dishwasher. The cabinet is located beside the sink (see attached photo for reference). Work will involve removing or resizing part of the cabinet and ensuring the space is ready for appliance installation.

I need a low budget kitchen cabinet made to replace a very old cabinet that will be removed for concrete repairs. Am trying to do a like-for-like replacement, not a kitchen upgrade. Is only very small, L shaped cabinet with sink needs to be made and installed. Is replacing cabinet in the front of the images - white base, blue top in the photos. Thank you.

Supply of material and installation of kitchen cabinets. I am looking to extend my kitchen with additional storage space. You are welcome to give your quotes. 1 tall pantry on left marking and cabinets over the sink on right.

New oven does not quite fit existing built in hole to allow door to open. Think it needs either fillers installed to bring oven forward or cabinet height extended around 5mm

I currently have a whole corner of my kitchen cabinetry which has gone unused due to the current setup of the doors. I am after a cabinet maker to see if the doors can be modified to accomodate a corner. Price opening door from two standard doors. Price negotiable

We would like all our timber kitchen cabinets and adjacent joinery sanded and re-varnished.

The overhead kitchen cabinet must be properly attached to the stud behind the Gyprock wall.

I've recently had a new rangehood installed and require the cabinet door above it to be shortened to accommodate it. Current door height is about 713mm and needs reducing to around 630mm, but will require you to please measure and confirm. Thanks

- install 4 (general power outlets) gpos for the following (electrical materials included); fridge, rangehood, dishwasher, benchtop. -Remove exisiting sink and cap water. -convert copper plumbing to pvc - modify following cabinets:- 1200mm base -> 600mm oven base 1200mm base -> 600mm sink base 450mm base -> 200mm spice drawer -install cabinets on wall, level, cut in appropriate services. - install end panels, fillers, and kickboard. -afix doors and handles. - Materials to be supplied by owner or reimbursed. Items include but not limited to additional fixings, kickboard, ikea cabinets if existing cabinets poor condition (as discussed), ikea 200mm spice drawer. - View all the details of this offer: https://www.airtasker.com/offers/01K29WX0E2VP6FMM8CG581XTK0

Existing built under Bosch dishwasher (SRU53E15AU) has conked out. We’re looking to replace it with a full size (60cm wide) model (not yet purchased, but likely an LG QuadWash). The existing gap needs to be extended by 15cm to allow for installation. Large corner kitchen cabinet to be adjusted accordingly (see pictures below). Seeking for work + materials from qualified cabinetmaker.

Remove the current cabinets and bench top from the kitchen and replace with new ikea cabinets and timber bench top. All new stuff will be sourced by us. Dont need to worry about disposal. Includes 4 base cabinets (2.4m), timber bench top (3m) and 2 mounted wall cabinets. One of wall mounted cabinets holds range hood. Bench top extends over under-counter water heater. Doors and shelves removed already. Hoping to get done before 4th August.

Drill a hole in kitchen cabinetry to allow a power plug through and have it finished off with a ‘sleeve’

We need the cabinet above our fridge cut so it can be raised up to fit our new fridge underneath. See photos. The fridge space right now is 850w x 1710h x 870d (and 622d on the left side). The fridge is taller than we have room for - its dimensions are 835x1787x730mm. The fridge's depth and width are OK, it's just the height that's a problem. So this task is for you to help us out. We need the cabinet taken off the wall to have some height cut from it, then mounted again 80mm higher up. To try and be ultra clear - new fridge is 1787mm high but the current fridge space is only 1710mm high. So there is an 80mm difference. We need that extra height to fit the fridge, which requires cutting the cabinets shorter. There’s 45mm of space to move it up, so the cabinets would be cut shorter by 35mm and moved up 45mm.

Need someone to take a look at this hettich hinged door. I’ve taken it off, it doesn’t close fully and is fouling despite adjusting the hinge screws.

I would like my kitchen cabinet fix as it loose small screws

Modify existing kitchen cabinet to fit a dishwasher. As in photos, Dishwasher to go on left (next to stove). Right side cabinet to be modified to either open cupboard or just a blank using existing door materials. Measurement from left side to corner is 640mm

Recently moved. Our fridge is ~800 wide and doesn’t fit into existing cabinetry which is ~760 wide. Looking for someone to come and adjust cabinetry to fit the fridge.

I need kitchen cabinet drawer stopper to prevent sliding out completely. For the second drawer only.

4x low cabinets have been assembled, 1 more base 800x370 cabinet + fridge cabinet require assembly. I need the cabinets hung and levelled on wall. Feet also need to be installed. Must have laser level, packers + tools to complete job. Preference will be given to taskers who have experience with the Metod system. 🛠️

Kindly requesting a cabinet maker / carpenter to adjust kitchen kabinet to fit in a dishwasher. Bosch Dishwasher measurements: Product Height (mm): 815 Product Width (mm): 598 Product Depth (mm): 573 Kitchen cabinet measurements: Height: 870 Width: 615 (this includes the sideboards which would need to be removed and replaced by a support structure - the photos should help to understand what needs to be done).