Find an experienced handyman in Glenwood NSW

I need someone to please fix a hole in the wall at home, it’s plaster and requires patching. Once fixed I will do the colour match and paint myself. It’s quite a tiny hole. I need someone this week before Saturday. Any times after 3pm (as late as needed) would be chosen over an early time slot as late arvo really suits me better. Any Q’s please ask!

Need to replace chandelier (remove exisiting one in and hang up new one) in the staircase.

Need closet fixed to give additional support to slabs. Also, fix rails for the garage sliding doors

Previous wall hole was fixed by someone but its not fixed right want to get it done asap in a nice way..as you can see in pictures i dont want that difference to be visible

I'm looking for an experienced tradesperson/installer to assess and install a heavy duty pull-up bar above an external garage side door in Glenwood. It will be used for strict pull-ups, kipping pull-ups, toes-to-bar and muscle-ups, so I need someone confident with structural masonry fixings and dynamic/cantilevered loads. Reference product: Rogue P-4 or similar. I have not purchased the bar yet and want advice on suitability before ordering. (See: https://www.rogueaustralia.com.au/rogue-p-4-pull-up-system-au) Key dimensions Door frame: 900 mm wide Slab to ledge below gutter: 2,330 mm Top of door frame: ~2,080 mm Space above frame: ~250 mm Rogue P-4: 1,321 mm bar width, ~762 mm projection, adjustable bracket spacing up to ~1,219 mm Preferred setup: centred over doorway, with both mounting frames completely clear of the door frame and fixed securely into masonry either side Door opens inward Photos attached show the external rendered wall, internal exposed-brick side, and intended position. Please assess masonry suitability, lintel/opening, fixing locations, anchor type, bracket spacing, edge distances and clearance for kipping/muscle-ups. In your offer, please note relevant experience, whether you can supply appropriate structural fixings, and whether you recommend inspection before purchase. Priority: safe installation suitable for dynamic bodyweight training.

Garage door is bent/buckled at the bottom and not sitting straight. The centre support/bracket may also be damaged. Looking for someone experienced with garage doors to inspect, straighten/repair it and make sure it opens and closes properly. Photos attached showing the issue.

Pergola panel repair, pergola roof cleaning, gutter maintenance as there is a leak

Sagging plasterboard ceiling repair Upstairs plasterboard ceiling has separated from the timber roof framing and is sagging approximately 35–45 mm at the worst point. Roof framing appears straight and plasterboard appears dry. Looking for an experienced plasterer to assess whether the existing ceiling can be progressively lifted and mechanically re-fixed, or whether affected sheets require replacement. Roof-space access available.

Fly screen door lock stuck inside. Need to replace it. Have bought a new lock. See the photos.

I’m looking for a licensed and experienced electrician to install 2 ceiling fans in my home. Both locations currently have existing ceiling lights, which need to be removed and replaced with ceiling fans with lights. Work required: Remove the existing ceiling light fittings. Install 2 ceiling fans with lights in their place. Check the existing ceiling structure/joists and confirm that the ceiling is structurally sound and suitable for supporting the ceiling fans before installation. Install appropriate mounting/support brackets as required. Connect the fans to the existing electrical wiring. Install/control the fan and light switches as appropriate. Test both fans and lights after installation. Clean up the work area after completion. Important: Please do not proceed with mounting the fans if the existing ceiling structure is not suitable. I would like the electrician to inspect the ceiling and advise if any additional structural support is required. Requirements: Must be a licensed NSW electrician. Please have experience installing ceiling fans, including checking/strengthening ceiling support. Please include labour and any standard mounting hardware in your quote. I will provide the ceiling fans. Location: Glenwood, NSW Please quote for the complete job for 2 ceiling fans.

I need a handyman or ducted vacuum specialist to reinstall and securely remount a Premier Clean Typhoon ducted vacuum power unit back onto the wall. The unit fell forward because the original wall mounting bracket pulled out of the drywall. It is currently being temporarily propped up by a ladder. Tasks required: 1. Securely remount the wall bracket back onto the GYPROCK (plasterboard) wall. Because of the weight and motor vibration, this will require heavy-duty hollow wall anchors (like toggle bolts/Snaptoggles) or being screwed directly into the timber wall studs. Standard plastic screw-in wall plugs will not work. 2. Realign and securely reconnect the white PVC inlet pipe attachment where it enters the wall. 3. Ensure the low-voltage wire connections and main power plug are safely intact. Please bring a stud finder, appropriate heavy-duty wall anchors/screws, PVC pipe cement, and standard tools. Photos attached.

I have two old fans that needs to be replaced by new fans that I will supply

Install Easy Shed Off the Wall Garden shed 2.25m x 0.78m includes fixings and ramp. There is a small slab (50cm squares) in front of it that needs to be broken down (I can keep the rubbish with me).

Airtasker Task – Inverter Shade & Environmental Protection Installation of Environmental Protection and Shade for Existing Inverter I’m looking for an experienced handyman/installer to install environmental protection and a shade structure around an existing inverter at a residential property. Scope of Work * Install the supplied environmental protection components and shade structure. * Securely fix the structure in place. * Ensure the installation is stable, weather-resistant and suitable for the existing inverter location. * Maintain adequate ventilation and clearances around the inverter. * Ensure the inverter remains accessible for maintenance and servicing. * Complete minor adjustments as required to achieve a neat and professional installation. Important Details * All materials are supplied. * Installation labour only. * Existing inverter is already installed. * No electrical work or modification to the inverter is required. * Standard installation expected to require 2 people for approximately 1 day. * Installer to provide normal hand/power tools required for installation. Looking For An experienced installer/handyman who can complete the work safely and professionally. Estimated duration: 1 day Workers: 2 people Materials: Supplied Location: [Sydney suburb] Budget: $1,800

looking for roller blinds supply and install, shoot me the quote for motorised and non motorised for double layer black out and interested if designer print is valuable, approx size 155 width 144 height

I have two shower screens in my house and I want to change them and replace with a new one Can buy the screens myself just need someone for removal of old and installation of new one

Removal of dishwasher, kitchen sink, kitchen tap and under bench dishwasher and reinstall new appliances into the same location

Need Gyprock repair, patching and painting for few areas of the house. Also need a kitchen drawer (I have the drawer face) needs to be reattached. I can supply the required paint.

Need a handyman to help fix broken door and glasses. Possibly replace complete door.

Need help with fixing one bent garage door and supply and install 2 single garage panelled door opener in Glenwood area.