Find a professional gate installation in West Brisbane

We are wanting a gate installed down the side of our house, using aluminium pool fencing 1200 high. The gate will go across grassed section and will be a bit over 2m. Then a fence panel from the edge of the garden to the concrete fence.

Need someone handy to fix the front yard gate, some panels have rotten.

Needs to install 4 curtains rods and repair side wooden side All parts supply. Need handymen to do the task only.

We would like two side gates on either side of the house to secure the backyard in preparation for a dog. One side is about 1.66M and the other side is 1.77M wide. Open to timber and aluminium options.

Due to dry rot, I need a fence gate post removed and replaced. The post is 100x100 mm square and stands 1800 above ground. The quote should include the supply of a hard wood post.

Internal wooden gate for top of the stairs to make it safe for children

mount wooden gates on new pillars 2 x 2.48m (w) & 1.2m (h)

The side gate has snapped off the hinges due to rust and needs to be reattached. A few of the wood fence mailings also need to be repaired. Looking to get this repaired pretty soon. Please send through a rough quote for the job

The Gate opens internally and goes up a small slope up the driveway which allows a gap big enough for our dog to escape underneath the gate. I want to have it moved to open externally and down the slope of the driveway so the bottom of the gate can close with a lot smaller gap on the bottom and prevent the dog escaping. Options to install an electric gate motor and also the change gate material to aluminium slats or similar to faciliate air flow for electric gate

Investigate the cause of leaking roof. The leak is near the roof-wall junction and in the in the vicinity of the timber elements. Provide quote to rectify.

I need my current fence removed and replaced either a fence in this style. With a driveway gate (approx 3.5m wide) with a sliding electric mechanism, and a lockable pedestrian gate. Total length of fence- 24metres Height of fence- 2m- with the scooped sections down to a height of 1.6m

Fence not damaged just came down in cyclone Pool gate 1 of the old dynabolts has broken and needs a new dynabolt or equivalent. Both ends of the small fence need new hole drilled in brickwork and a new dynabolt or equivalent to hold in place. Sorry no picture of gate .

Fence needs to be put back in place only small fence not damaged just needs to be put back in place . Pool gate need news screws closes ok but not a safe gate .

Fencing linked to side gate needs to be re-built. New clothes line mechanism to be attached to brick wall. Minor pool fence repairs

Large Wooden remote gate is rubbing on concrete driveway. Needs to be adjusted so it does not rub on the driveway and the arms for remote need to be refixed to block wall. The gate should be adjusted to match the height of the RHS gate. This job would require a skilled tradesman / experienced handyman to complete the task.

I'm wanting to get an electric gate installed at my property, ideally a roller gate rolling from right to left in the photo. Wanting an aluminium gate in the same style of fence.

To fix the fence , slab came off and fix the hinge of the gate

The front gate needs to be repaired the end panel near the lock is loose and needs to be drilled to be secure. The panels in the door are out of alignment and might need moving/cutting back to be even so the gate is strong and lock properly.

I need a timber side gate 1.8m high by approx 1.2m wide with metal frame- supplied and installed on a new build home in Graceville.

We have a Centsys Centurion D5 Evo 240V Automatic Slide Gate Motor powered by a outdoor electrical socket, with a backup solar panel. Recently, plugging in the motor has been tripping the power supply. We need a professional to inspect and resolve this short-circuit issue. Additionally, we find the solar panel unnecessary and suspect it may be contributing to the problem. We would like it disconnected and removed. Please ensure you have experience with gate motors and electrical systems. Thank you.