Find a professional gate installation in Blacktown

As attached in the pictures, left side of the gate is a bit broken where it can't stand properly may be the screws are loose and because of that, the gate is not opening/closing with the latch properly. I need someone to fix the gate so that it sits firmly without any issues

Extention of boundry fence from corner to the both side length 4.8m and 4.2m, hight 1.8m plus side gate length 1.6m hight 1.8m . See the photos, need to extend from blue board to the corner. Materials are provided

The colorbond side gate (80cm ×180cm)is fixed to a 50mm square pole using two Hinges. The side post is fixed to the Garage brick wall using 5 10mm dynabolts. The gate is locked to another 50mm square pole using D latch. D latch offers some movements in the locked state and due to that wind creates rattling and the side post is coming off from the side wall. I need to fix the gate permanently. 1. Need to replace dynabolts with chemical threaded anchors to the wall. 2. Install 1 or two locks(may be up and down ) which locks the gate securely (no movement if the gate when it locks) 3. Install a stop plate to reduce the wind pressure.

Cirrent side gate is color bond gate with height 180cm and width 80cm. The gate is fixed in a 50mm square post attached to the sidewall using dynabolts.. Because of the heavy wind the post is coming off from the wall. I need to replace the gate with a metal/aluminium slatted gate

I need a plumber to investigate and fix a strong stink/odour coming from the toilet at Red Rooster, Mt Druitt.

All Materials for gate is supplied. I only need a labourer to install a double gate on a concrete drive way. 2.4m Width + 1.8m High panels

Need a gate latch installed. Old one broke, must supply screws that can be used for color bond fence

The roller gate in my garage is not working because the orientation is misaligned. The job is to fix the orientation and make it working automatically. I don’t have a remote but we can quote it separately hence remote is out of scope

Need someone to put back the hinges

Just need a power tool to put the hinges back. (Bottom)

I need to get my backyard door gate repaired and secured with a heavy-duty lock. I want a permanent solution that is strong and weather-resistant. Could you please buy a suitable heavy-duty lock and install it for me? I have attached a photo of the current gate setup for reference. could you please send me photos of the heavy-duty lock options that would be suitable for this door gate, so I can confirm? Also, please provide me with a reasonable quote including the cost of the lock and installation.

Install a perma wall mounted baby gate above stairwell

Need this baby gate installed Was attempting it but failed One side has a wooden solid panel which is to the right of the stairs. The other side is gyprock. So need a pro to install is so that it's solid. The gate fits. You can see the photo of the brand. It's found in Bunnings. https://www.bunnings.com.au/perma-child-safety-1-4m-white-wide-retractable-gate_p0466947?store=7342&gclsrc=aw.ds&gad_source=1&gad_campaignid=11071326645&gbraid=0AAAAADtbEB-hKPSnvznPYAhrEpeMXplF3&gclid=Cj0KCQjw-NfDBhDyARIsAD-ILeDg0VBzms2FjmoTqRD4D0PY-Tf1QBuvvtoRS22-r5SHiFJV84yqB7kaAlP6EALw_wcB

Side gate needs a lock, see pic attached

One my friends moved the fencing gate and the lock below was bent. I need that to be fixed so that the gate can be securely closed. The bent knob is as shown in the pictures.

Colorbond fence gate collapse after strong wind. Reuse existing frames and sheets since it is still in good condition. Screws all gone and need to be replaced. Reattached the gate.

Dog has punch out the colorbond from the frame. Need gate repaired

Backyard gate to stop dog from entering an area.

Need infill sheet replaced for colorbond gate. 2.8m W x 1.8m H. Install drop bolt, safety latch keyed lock. Gate to be raised by 50-60mm while refixing. End posts, stiles, frames etc are all reusable.

Help me mount a Eufy doorbell to a front gate properly and ensure it works well. I’ve already set up the doorbell to sync with the chime, so just need to drill the mount to the front gate.