Find experienced local fencing contractors in Leichhardt NSW

Seeking a dividing treated pine timber paling fence between rear open space: - Length approximately 7.1m. - Height approximately 1.8m to 2.1m due to slope of site (TBC). - Single layer of timber palings to both sides please. Not lapped due to double sided palings. - Timber palings with flat tops (no shape please), 100mm wide preferred. Reference image attached. - No timber capping to top of fence, please (tend to bow?) - Direct rear lane access. - Gal posts are preferred. Please allow two additional posts beyond the standard post spacing to support weight off fence. - "Home" end of the fence abuts external brick wall. - Site is ready to go. Existing fence is already removed. Thanks for looking.

We have a metal fence/side gate that requires repair. Also, we have another wood gate that needs to be reattached. Price is $200 per gate ($400 total)

Handyman/builder required to customise a baby gate to fit the bottom of our stairs. We did have a baby gate installed on the stairs but it was broken easily because it wasn’t screwed into a stud and there doesn’t seem to be a stud in the part of the wall we need the gate to be attached to. Therefore, I believe a piece of wood needs to be used and cut to shape to secure the gate to the wall. I require a builder/handyman to install a secure gate. The stairs are wooden and there is metal railing with glass.

Need professional fencing/gate company/person to (by 18 December): 1) remove existing broken swing gate at side entrance of residence (see photos) 2)procure and install a new aluminium slat swing gate with lock (exact type and colour to be agreed) Gate dimensions are roughly 90cm W x 180cm H.

Attend Leichhardt Oval at 4:15pm today and move 26 plastic fence panels + posts about 20m or so to be near the exit.

Wrought iron heritage gate needs new brace added to bottom and pivot installed. Post needs to be replaced. Gate needs to be aligned so ball roller works easily, Essential that offers are from those experienced with wrought iron. Offers from previously posted deleted job welcome.

We need to have our fence fixed back to the brick wall and the wire for the Jasmine to be re strung as it snapped and Jasmine is not fixed to fence anymore. See photos attached

Install letterbox within fence. Will require cutting hole in timber fence.

I no longer need these I need them taken away

Replacement the fence including rusty columns and painting.

I need a metal gate to be installed on the existing post. I have purchased the gate and strap and hinge set. I can pay for timber screws and installation cost.

Quote needed for removing and disposing of an old colour bond boundary fence in back garden 14m long. Replacement with a treated pine paler panel fence with concrete plinth and posts -14m long and 1.9m high. Could be either capped at top or ended with matching pine lattice extension. Fence is next to some border plants but can cut some down if needed. Boundary will be marked out by the surveyor. Located in Leichhardt. Garden access from lane.

4m wrought fence replaced by timber or other. Alternatively wrought iron gate repaired.

Remove old metal fence panels (9.4m) and associated timber rails, replace with new rails and pine timber panelling. Old fence posts are still good enough to support new fence.

Demolish existing fence approx 30m and remove rubbish Supply and install treated pine 1800 palings with capings 50x50 steel posts Must be licensed and insured

Lift up temporary construction fence (1 panel) and put it to close the garage and prevent access. Make safe and restrain from wind

Wooden gate has had its top hinge pulled out of the gate post due to windy weather. A long fence paling adjoining the gate post has also split as a result. We require the gate to be reattached to the gate post and the fence pailing to be replaced.

Remove an existing timber side gate and buy/make a new timber one and install it.

I need a Paling fence 12m long X 1 mt

Horizontal post on white picket fence has rotted 1/3. Either need to do a repair on this part or replace and re-drill pickets. Pickets must match existing design as we are in a heritage conservation area.