Find experienced local fencing contractors in Camp Hill

Would need you to make a fence 1200mm high so it joins with the glass panel and forms a proper barrier. The horizontal slats that I've highlighted just need timber pool fence wedges supplied and screwed into them so they aren't climbable.

My pool fence has deviated or buckled recently, which is causing the gate to be left ajar. Need it reset so it closes properly.

the two fence posts are tilted, need to bring back to right position.

One pool fence needs to be reinstalled. Glass is in good order.

We need a side gate and short fence section supplied and installed at our home. Gap between fence and house is approx 2.5m (and would like a gate that is hopefully approx 2.0m in width). Scope: • Supply a large prefab gate (eg Bunnings or similar) + hinges + latch + galvanised post + wood pailings + fixings. • Install gate with hinges on the right-hand side (may need gal post fixed against retaining wall or set in ground). • Add pailings to gate to bring height to approx 2.0m. • Fit latch. • Attach about 6.0m of 1.2m-high pailings to an existing fence. Open to suggestions too if there’s an easier or better way - we’re easy to work with, easy access to work area and parking. Looking to get it done before 23 Aug so we can secure side of house. Any questions please let me know. Cheers John

21m of lap and cap fence. 2 sections ...~17m and then ~4m. On top of block retaining wall. Good access.

Timber Fencing - replacement of entire 20m front fence. Supply of materials required, as well as installation of fencing and two gates: one path gate and one driveway gate. The existing fence will need to be removed. Fence palings are 1.2 high. Quote should be for treated pine. And would be helpful to know a price with/without painting (paint and primer supplied).

Need a timber fence built on a flat block in Camp Hill. Approx 56m total - can supply materials if needed or you quote to supply and install.

Our current timber fence needs a new post (90x90) added to stabilise the panel. This involves digging a 60cm deep hole 20-30cm diameter, mixing concrete in my wheelbarrow, placing the post upright and level and supported for concrete to dry. I would say it's a 2-4 hour job for a fit person. I will supply post, concrete & wheelbarrow. Need a spirit level.

Unfortunately, our pool fence is failing a pool safety test. One of the glass panels is coming away from the pool - it’s noticeable. Someone with experience in this. Two men required I would imagine to remove panels - as I think the poles/supports need tightening. Must be done fairly urgently.

I'm looking for an experienced bricklayer to build a 1.5m high brick fence in my front yard. Please see attached image. Thanks

Timber fence has been damaged due to storm and tree coming down.

We require the front pailings to be nailed into the bottom rail to adequately secure to stop our dog from getting out. This should be done with a nail gun with a minimum of 2 galvanised nails to each pailings from the house side. There are some shrubs to some areas which may make it a little tricky. We have a 20m frontage less driveway gates which are powder coated aluminium.

We need fence pailings installed on our side of an existing treated pine fence (new, refer photos). The fence is approximately 10 meters long and 1.8 meters high. In addition, we’d like the top of the fence cut with a circular saw/straight edge to ensure it’s consistent and level. Details: • Treated pine fence. • Approx. 10m long, 1.8m high. • Easy access to the site. We’re looking for a professional and tidy finish. Quote to include materials and AirTasker fees.

I am looking for someone to source and install a side gate at our house. Preference timber that can be painted white. Width is 2m and would like 1.8H . There is a 50cm x 50cm overhang on one side of the fence (garden beneath the side of the house) that also needs to be filled in.

Rein force existing front fence post with an additional post (hard wood) to one side eg dig hole, attach hard post to existing fence, secure with concrete to base.

I small piece of fence and a gate built. It encloses a space at our business. gate approx 1800mm high by 850 wide. Fence return 800mm long. Materials supplied, need tools.

Need to build a 12.5m fence between two properties: - pine timber paling fence - need price for three options: 1.8,2m and 2.4m tall fence (need to agree with neighbour on height hence three price points would be handy) - timber palings to overlap each other by a cm or two as per example photo (~140-150 palings) (i.e. like weatherboards, but vertical) - footings will need to be either concreted in or bolted down under row of pavers, with minimal disturbance to other pavers (I think there’s an old slab underneath the pavers, just not sure how far it extends out) There is a single car driveway access for materials etc

We have a side gate that our dog escaped under. We need someone to build or attach something to the bottom to prevent this from happening. It will need to be opened and closed so bins can be taken out etc so functionality of the gate needs to remain. Let me know thoughts and offers!

Hi There, need a Recessed Aluminium Letterbox to be attached (sit behind) to a slat timber fence.