Find a fence installation professional in QLD

I need to do following tasks: - Build and install 2m x 1.8 m gate wooden gate. I have timber on site. You need to provide hinge, lock, screws, nails etc. - Install 9 X 2.9 m L cladding cap over all ready installed exterior cladding. I have all the L cap on site. You need to cut few of them before installing. You need to provide glue or black screws to install them.

Remove an existing aluminium fence from a property in Narangba and install it at a property in Deception Bay, replacing the existing timber fence at that location.

Hello, we are wanting to get a privacy fence built on our patio. It will go on the inside of the existing besser block fence, and just be to the normal boundary height of 2.1m. Have attached pictures of the area and then the look we are going for. Would prefer someone to come out and quote, but I can try and give accurate measurements if needed. Will reimburse for all supplies etc. Thank you

Looking for someone who can install 2 picket gates. Have already got one of the gates. Gate 1: Height 1.8m width 1 meter Have already got a gate of 1.8x0.9m Gate 2: Height 1.8m Width 0.7 Need a gate

Fence Post has rotted out at bottom and needs replacement. This is a support for the colourbond fence. Exact Job: Remove adjacent pavers to existing 3 Colourbond posts. approximately 250 x 250 area. Ground will need to be excavated approximately 600mm for new post to be installed. New 100 x 75 mm H4 posts to be installed in holes, plumbed up and concreted in. Trowel finish at base of posts to fill in missing pavers. Cut down appropriate lengths of galvanised threaded rod. drill 2 holes in timber post and existing colour bond post ( top and approximately 600mm up from ground.) Utilising m12 nuts and 50 x 50 galvanised washers. Bolt/washer either side of post, followed by plumbing up fence then using the same method nuts/washer to clamp in place.

One side of our fence fell down. I need you to take the old fence to the tip and install a new wooden fence. You will have to dig the post holes and install the fence. I'm negotiable with price. We will supply the materials. It is 54 metres long. Thank you

We have an existing pool fence that needs to be removed and replaced with a new one. Posts concreted. The new fence will be approximately 20 metres across two sides (+ standard height) and include 2 gates. Looking for the standard black aluminium pool fencing, with materials supplied as part of the job. Scope of work: Remove and dispose of existing pool fence Supply and install new black aluminium pool fencing Install 2 compliant pool gates Ensure installation meets pool safety compliance standards Timing: Flexible on dates – happy to work around availability. Please include labour + materials in your quote if possible. Located in Ipswich.

Timber gate in corner needs new post to attach gate with hinges. Collapsed 5 months new colour bond on the back boundary will be fixed by original contractor. Please see photos. 1st photo after the storm 2nd photo taken from inside garden, it was before the storm, in perfect condition

I need new sliding gate motor supplied and installed

I have purchased 2350x600 fence extension panels (3) for my Colourbond fence. I just need the installed. https://youtu.be/KXb_rdje5TY Ideally Wednesday or Thursday this week.

Just purchased a house previous owner had sliding gate customs made with post and parts but never installed.can I have price to get it installed

Pool gate bar been damaged by trespassing, replacement required

Footing of a colourbond fence was accidentally excavated, when backyard was excavated. Fence is now beginning to lean for that one fence panel, need footing replaced underneath artificial turf. Please include cost of materials in the quote.

Looking to get colorbond fence and electric gate supplied and installed in my front yard, also old fence removed. Pic attached for reference of measurements

I am settling on a townhouse in Everton Hills on 02/03/2026 and require a side gate to be supplied and installed on 03/03/2026. The gate will run from the existing brick wall (as shown in photo) across to the boundary fence. It may be possible to bring it slightly forward toward the front of the laneway to utilise an existing fence post if that makes installation easier. Approximate measurements: • Width: 1 metre (measured from fence post) • Height: 1.90 metres I’m open to either: • Timber gate • Colourbond gate Please provide separate quotes for both options including supply and installation. Scope: • Supply all materials • Install posts (if required) • Securely fix to brick wall and/or fence • Hinges, latch and all hardware included • Clean finish suitable for townhouse complex Access will be available from settlement (afternoon of 2nd March if needed), but install must be completed on 3rd March. Please include: • Total price • Timeline Happy to arrange a quick site visit before settlement if required.

I need 50 fence palings replaced 1.8mtrs high 3.9m long

9.6metre colour bond fence to be put up

Our Colour bond fence is in good condition, however the metal that goes into the concrete has rusted, we need a quoted for the repair on 4 or 5 supports to be sorted

I need a fencing panel installed to close a gap in my fence. Previously there were banana trees in the gap but the trees have now been removed and there is a gap around 4m wide. I think it will need a single post installed in the centre to support the rails. I am looking for a standard paling fence.

I am looking for someone to remove and dispose of existing wire/timber fence, and to then supply (pick up) and install new pool fence with gate (approx 7.5m) into concrete slab. Existing timber fence - this is easy to remove - needs posts to be cut at slab level and wire snipped. New fence - will join existing pool fence section and will go into concrete slab. Access to property is very good and I’d be happy to assist if needed. I’ll pay for the materials separately - the cost here is for your labour and disposal of old fence.