Find a fence installation professional in Outer West Sydney

Remove Farm type metal fence and install new Colorbond fence around 35 meters. Need 1.8 meter high, Color Heritage Red frame with Primrose sheets. Happy to supply products as required. Trees and plants near fence will be removed next week. Open to pricing estimate on the labour

Installation of 5 Screenline fence extension panels. Consisting of 4 full panels and 2 partial panels. Installation guide: https://screenlinesystems.com.au/pages/installation-guide

Install 8 posts (not supplied) to hold wooden gates at either side of our property. Install gates and fencing between the gates.

I'm wanting an aluminum fence installed 10m in length.

Looking for an experienced pool fencing contractor/fencer to come to Cranebrook NSW and quote on rectifying one section of our existing pool fence. We have recently had a pool compliance inspection and have been advised that this particular section needs to be rectified before we can obtain our Certificate of Compliance. What we need: Inspect the existing fence and our pool non-compliance report. Advise on the simplest and most cost-effective way to make this section compliant. This may involve replacing the section of fence, increasing its height with a suitable extension, or another compliant solution. If replacement is required, we would like it to match the existing fence as closely as possible. The area is near a retaining wall/pool shed, so onsite measuring and potentially some custom fitting will be required. Any proposed solution must meet the relevant NSW pool fencing requirements and be suitable to pass our reinspection. We are not looking to replace the entire pool fence — only rectify the section identified as an issue. Location: Cranebrook NSW 2749 Budget shown we know may not cover everything so inspection is going to give a better idea. Once we know the recommended solution and cost, we can work on and proceed with the work as soon as possible.

Looking for an experienced fencing installer to install aluminium fence posts only. Fence panels and gates will be installed separately later. The fencing system is pre-manufactured and DIY-friendly. Posts are already supplied pre-cut to the required sizes, so no general cutting is required. Only a few posts may need minor trimming on site due to the slope/fall of the land to achieve the correct finished height. Work required: * Accurately measure and set out fence/post positions and boundaries. * Maintain exact spacing so the supplied fence panels and gates fit correctly later. * Dig approximately 23 post holes – 600mm deep. * Install and concrete aluminium posts. * 3 additional posts require drilling/fixing into existing concrete. * Ensure all posts are straight, plumb, correctly spaced and aligned. * Minor trimming of a few posts if required due to changing ground levels. * Clean up after completion. Materials supplied: * Black powder-coated 6063-T5 aluminium posts. * Standard posts: 65 × 65 × 2mm. * Most posts are 1.8m long. * A few are 2.0m long to accommodate the sloping ground. * Larger gate posts: 150 × 150 × 3mm. * Concrete bags will be supplied by me. Important: This job is for POST INSTALLATION ONLY. No fence panel or gate installation is required. Installer should have fencing experience and own post-hole digging/drilling equipment, levels and an aluminium saw for minor trimming. Please provide a fixed labour-only price for the complete post installation.

Looking for an experienced fencing installer to install a black aluminium slat fence and gates. Scope of work: * Mark fence line and ensure boundaries are straight and accurate. * Dig 23 post holes (600 mm deep). * Install aluminium fence panels and gates. * Concrete all inground posts. * Core drill 3 posts into existing concrete. * Cut aluminium posts to the correct height where required (bring your own aluminium cutting/drop saw). * Ensure gates are aligned, level, and operate smoothly. * Clean up the site after completion. Materials supplied: * Aluminium fence panels, posts, gates, screws, and accessories. * Concrete bags. You need to bring: * Post hole digger/auger. * Core drilling equipment. * Aluminium cutting saw. * All standard fencing tools and PPE. Requirements: * Proven experience installing aluminium/slat fencing. * Ability to accurately set out fence lines and levels. * Own tools and transport. * Please include photos of previous fencing work in your offer. Looking for someone who has done similar aluminium fence installations before and can complete the job to a high standard.

Fence Removal & Reinstallation – North Richmond (Materials Supplied) We're looking for an experienced fencing contractor to remove and reinstall a powder-coated fence in North Richmond. This is a replacement installation only. The original fence was supplied with a manufacturing defect, and the supplier is providing all new fencing materials under warranty. The replacement fence will be on site and ready for installation. Scope of works: Remove approximately 17 lineal metres of existing powder-coated fencing. Install the new replacement fencing. Reinstall 2 gates. Existing posts are to remain – no new post installation required. Fence is an SHS-framed, powder-coated steel fence with tubular infill rails. We're ideally looking for someone available Tuesday 21 July, or as close to that date as possible. Please get in touch if you're experienced with powder-coated fencing and can provide a quote for the removal and reinstallation.

I need to install 62 meters of fence. Fence needed is 1.8m height with 2.4m length. Will need all material and installation. Ground is already clear and ready to install. 24 panels approximately.

The chain fence on site has broken at the bottom along one section. As photographed. Looking for someone that has a possible soultion. Noted as $10 budget for now, as not sure what work is currently required

Supply and install 14m of colourbond fencing with a gate one side and double gate the other

need a colorbond fence installed approximately 1.8m high by 18.5m long with 2 gates potentially and old timber fence to be removed.

Please see below - 1 x gate/panel - 1 x panel only - 1.8m high - approx 1m and 1.8m opening

I have wooden pieces attached to side of my house. I want to replace it with colorbond gate to give access to my backyard. I need someone to bring and install new/used colorbond gate and removed wooden piece

Complete installation of automatic kenner gate opener including power box installation

Install 20m of colorbond fence, 1.8m height at the back yard and 10.5m of 1.2m height monument color alum horizontal slat fence at the front, and 2 single gates, one on the front and the other on the back yard. Please quote based on cost per meter.

Fenstar aluminium slat pedestrian gate with 2 posts to be assembled and installed at side of the house. Width 1240mm, height 1800mm.

Install a farm gate. Dig post holes, concrete in posts and mount gate in driveway.

Fence panel replaced approx 3.1m and some privacy screens. For the grey section only.The posts are good just the panels are rusted and dont sit in the channels. For the privacy screens. There are 9 panels and just have to unscrew top and slide old lattice out and slide new privacy screen in then screw top back on. I'll get the materials from Dunn and farugia. I just need labour to do. You need to be experienced at doing fences.

Install a new colourbond dbl gate as the current one has dropped and not done well , fix and reinforce 3 -4 fence panels and posts on side fence