Find trusted local electricians in Caringbah

Hi, I’m looking for an experienced appliance technician to diagnose and fix my Bosch heat pump dryer. Appliance * Bosch Serie 8 Heat Pump Dryer, SelfCleaning Condenser * Model (E-Nr): WTW87564AU/09 * Installed in laundry, front access Issue * Dryer completes the cycle normally, but clothes are still damp at the end * Drying performance has dropped compared to before * No obvious error code, just poor results What I have already done * Removed and washed both lint filter inserts and refitted once fully dry * Cleaned lint around the filter area as best as possible * Unit is plumbed to drain via hose into the sink (not using the tank) * While at some jobs seems to do a good job, most are still damp What I need * Full diagnosis of the cause (airflow restriction, moisture sensor reading, fan/heat pump performance, drainage related self-clean issues, etc.) * Clean and service internal areas if required (I understand “self-cleaning condenser” models can still build up fine lint internally) * Confirm correct operation and advise if any parts are needed before proceeding Please include in your offer * Your experience with Bosch heat pump dryers, ideally Serie 8 * What your call-out includes (inspection, cleaning, testing) * Any call-out fee vs labour rate * Earliest availability * If parts are needed, please quote parts separately before replacing anything Location * Caringbah, NSW * Parking available: Yes Timing * Flexible, but I would prefer ASAP.

The flickering down light needs to be fixed or in case it is faulty replaced. The spare one is provided by us.

Need someone to Install light and hardwire it to my shop

We need a Britec adjustable dryer stand assembled (easy) and need our 50kg heat pump dryer (heavy) placed on top. It is going in a tight space but I’ve measured everything so it’ll fit perfectly.

A tall standing lamp needs a new cable

I have garden lights need tracing and get them working. may need to add additional ones.

Replace sealing light fixture and check sealing fan as it is not working

I have a pendant light that needs to be installed in the ceiling. There is a powerpoint in the ceiling it can connect to.

Licensed Electrician required to arrange the installation of LED signage and connect to power. There is a template with for drilling locations, sign placement etc. Note all products are 12V and must go through transformer, cannot be connected direct to power source. (last image is a render of how it should look once installed)

I’m wondering if something is possible. I’m wanting to put LED light strips behind the mirrors. The wall is brick and I’m wondering if there’s a way to connect the led strip to the ceiling lights which are down lights.

I’m wondering if it’s possible to put a power point on this wall. I know the only power source is this light switch.

I have a small hair salon and I’m wanting to know if it’s possible to put some sort of Bluetooth speakers in the ceiling? I’ve attached a photo of the ceiling and also kinda of what I’m thinking as in speakers. Not sure if this is possible or not. Thank you.

I’m looking for an electrician who can supply and fit a power point for me. I’ve attached two photos, on is the reception desk, that’s the wall I want the power point for and the other is on the other side of that wall where the switch board is. Preferably done tomorrow morning 22/8/25.

We’re looking to put dimmable warm down-lights in our new house in Caringbah. Our budget per down light installed including materials labour etc. Were budgeting for $35 per down light. See the floor plan. The total amount of down lights were not 100% sure ye. But around 40-60

I need an exhaust fan installed where an old one was. All ducting is already in place.

Needing old lights removed and 3 pendants installed. Needing 4 power points installed. 2 will be on a gyprock wall and the other 2 are on a brick wall.

Need to replace internal black and may be silver piece power point. Glass cover is ok. Small job @ Caringbah South.

I need to replace two old double power points to a new ones.

Electrician required to fit outdoor wall light, replacing the old one which is water damaged. I have purchased the new light so just needs fitting. All other lights operating from the same power switch are working fine, so reasonably sure the issue is isolated to the one single light itself.

Fault codes are coming up..no spark. Huskavana 401.motor is in a buggy.