Book a professional espresso machine repair service in VIC

Safety switch keeps flicking off. Supplies dishwasher and coffee machine

Shots are pouring too many mls. Ex barista and have done everything I can think of to make it taste better. I can not 😂 I think it needs some calibration and potentially new/sharpen of the blades

I have two breville creatista machines that need repair, 1. Is leaking and I think need a new brewing chamber. 2. The steam wand has stopped working and is asking to be cleaned after each use .

I need a plumber to do two jobs. My tap (as shown in images) came out and needs to be put back in - unsure if I will need to completely replace the tap but hopefully you can judge from photos. I also have a plumbed in coffee machine that I need to remove too. Please message if you need extra details!

My coffee machine does not have water coming through the group head. If I do a full clean and descale, it will work, but the next time I use it it won't pump water all the way through, eventually leaking out the back. There does not seem to be any obvious blockages when taking the machine apart. The hot water/steamer wand does not seem to have any issues.

SMEG all in one coffee machine has grinder set in forward position and cannot be reset.

Fix Breville Sage espresso machine at home in North Melbourne. Replace steam wand tip rubber seal, quiet motor rattle and inconsistent extraction. Quick service needed, no major issues just basic tune up. Bring tools. Must know Sage/Breville!

La Marzocco 2 group, Serie F870, Model 2AV Details from last service: Brew element has major scale breach, pump is seized, fan not running and solenoid exhaust manifold has some scale build up too. Did basic service while on site and replaced seals/shims/showers, replaced vacvalve o-ring, cleaned level probe, rebuilt RH steam tap, replaced filter, all other functions working otherwise. Checked/cleaned Robur, burrs starting to feel dull so may be worth replacing when go back to sort out other issues.

Rancilio semi professional machine located on counter top adjacent to sink. Need benchtop to be drilled to enable water and waste tubes to be fed through to water and waste supply. Needs pressure adapter fitted to water supply hose (supplied) and extension of existing waste hose (supplied). Should take about 1.5 hours max. Must have experience with plumbing

I have a coffee machine which has a Chinese plug installed. Looking someone to cut the wire and fit an AU plug

Vzug coffee machine model Ccsxsl60 has heating problem

I have a Breville coffee machine and the steam wand stopped working. We already checked the wand itself and that’s not the issue. All other parts working well

Got a new breville barista touch and I can’t figure out the grind and brew settings my coffees are coming out watery and bitter

Need someone to urgently look at my Nuova Simonelli 2 group coffee machine which is leaking water and not operating correctly. There could be somthing wrong with the heating element

Breville Oracle Coffee Machine is hot to touch and is long over due for a service.

Coffe machine is running too fast no matter how fine i go on my new vs6 varia grinder

My Breville Oracle has worked seemlessly for 6 years until yesterday when it got too hot and stream was coming out of it. I’m looking for an EXPERIENCED mobile repairman to work out the issues and replace parts if required

Our kitchen sink has started to smell. We’ve tried Draino but it hasn’t fixed the problem. There’s also an old water filter attached (might be part of the issue) and a coffee machine that needs to be disconnected from the water supply.

Job: Need a licensed sparky to supply & install a new 32A circuit from the switchboard to our coffee machine in the café. What’s needed: • 32A 3-pin GPO installed under the counter (machine connection point) • 32A RCBO at the switchboard • Run cable neatly under the counter from wall to machine (see sketch/photos) • All materials, labour & compliance cert included Thanks,

My Breville Barista Pro coffee machine has an intermittent issue — when starting steam or extraction, it sometimes stops after a few seconds, beeps, and does nothing. Other times, it works fine. Need someone to: • Inspect the machine • Diagnose the fault • Repair it so it works reliably Please bring tools/parts if needed and include total cost in your offer.