Find experienced local carpenters in Paddington NSW

Broken drawers in a cabinet that need fixing, some open, some don't and some are jammed.

We have a small circular cut out in the back of some joinery to feed cables and we need to increase the hole slightly so we can fit a hand/arm in. Probably an extra few cm each side so a hand can reach in.

I have a 2m high x 1.6m wide freestanding outdoor mirror made from 45mm x 45mm angled stainless steel. I would like to mount it to a wall and to do this I need to have tabs welded to the sides, bottom and top of the mirror frame. I have 9 mild steel tabs made up to weld onto the back of the mirror frame, 2 each side and top and 3 at the bottom. Because the mirror is so large, this is something that I need to get done on site.

Handle building material Dig a hole and remove dirt Assist carpenter

I need help to install an oak framed shaving cabinet in my bathroom which has white subway tiles.

Tighten two timber stairway posts. Requires fillers/ glues.

HI - I need a table built with legs and a table top that is 96 cm wide and 2.4 meters long as an extension to my dining room table. It doesn't need to be good quality wood, just sturdy as we'll be putting a table cloth on top of it.

I want to put some architraves on the door, but tiles protrude door jambs by up to 17mm in certain areas. Site inspection to provide advice on approach

Bathroom renovation The tiles protrude beyond the door jab by up to 17mm but only in a few places. I need the door jamb replaced and architrave installed, plus one coat of undercoat paint. Supply and install. 2 doors need to be done, but quote for just 1

I need a skilled carpenter to install architrave on door in bathroom. 1 x door, both sides The tiling protrudes the door jambs, so it’s unclear to me whether the jambs need to be replaced or if the architraves can be cut/shaved to accommodate. The protrusion varies and just two sides of the doors. In some sections it’s up 17mm There is also a section at the bottom on the door jamb that has written and needs to be replaced Please quote for supply and install, include one coat of undercoat paint. See pictures

Sand and refinish timber floor in small room (~9m²). Looking for experienced floor sanding professional (not handyman). Want a light Scandinavian/blonde finish with matte seal—no yellow/orange tones. Please include materials and 2–3 coats. Must provide photos of similar work. Prefer test patch before full job.

Patch and repair wall and plaster around top of joinery as pictured. Painting of wall behind joinery only I have the paint for the wall

I need a skilled carpenter to install architrave in bathroom. 2 doors, required architraves both sides The tiling protrude the door jambs, so it’s unclear to me whether the jambs need to be replaced or if the architraves can be cut/shaved to accommodate. The protrusion varies and just two sides of the doors. In some sections it’s up 17mm Please quote for supply and install, include one coat of undercoat paint. See pictures

Approx 14 metres. Timber quads. Finished with satin before install. Mitre joins to multiple corners. Studio apartment

To fit two lengths of skirting board joining at right angle corner. Length 1.20m and 3.00m. The wall has been scutched back to brick in places. The board is in two parts. A bottom plank with decorative top plank. Cut outs needed for power point and TV arial connection. Residential property, must clean up. Board can be cut if necessary on outside veranada.

Refinish the wooden bench and built in storage +BBQ overhang in my back yard

Convert open shelves 1200 x 2100 (3 of them) to have 2 x 600mm https://www.bunnings.com.au/lugna-110-silver-door-hinge_p0597229 hinged door. Could be MDF which we can paint. Also install one open hanging rail in open shelve in middle. Single open shelves could leave a few open at the top. Provide all material which we will reimburse on receipt.

Need a carpenter to build and install some baby gates for us (likely 3) and quite a few other jobs while here

I’m seeking a quote for custom joinery work in an existing bathroom and would appreciate your advice and pricing. Project summary The work involves modifying an existing bathroom vanity to include floor-to-ceiling base cabinetry and an integrated front-loading washing machine. No upper cabinets are required. The window, tiles and overall bathroom layout will remain unchanged. I would also like a small mirror vanity cabinet to go where the current mirror is. Before and proposed Picture attached for a rough reference

Wood/ timber expert to match a missing timber stairway balustrade (see photos) if not via the Airtasker ecosystem suggestions are most welcome.