Find experienced local carpenters in Maroubra

I need a tradie who is able to see if my current draw dishwasher can be changed to a full size dishwasher. Ideally person could do whole job I will need to be advised what size dishwasher needs to be purchased. Need full quote for all required

Looking for a carpenter to reverse the swing direction of an internal door so it opens outwards from the room instead of inwards.

Carpenter/builder required to enclose an area of patio and to seal off internal French doors

Install new door frame and door with hinges. Door is 2020 x 720 Install door handle and lock Carpenter to provide all materials including timber and solid door except we provide the door handle mechanism.

We have a large room that we would like to insert a separation wall. Use timber frames across 4m wide wall x 2.6m tall wall. Gymprocking to be done separately

We have side passage from the garage to the backyard. It's rarely used and not seen by guests but it is sinking away and needs replacing. It is approximately 4-5 metres in length

Carpenter required on hourly rate to finish off skirting install locks and hang a few doors

Hi there, I need a local handyman to carefully remove one single piece of timber skirting board located inside my kitchen's refrigerator alcove. This is a rental property, so it is critical that the board is removed cleanly in one piece without cracking the wood or damaging the adjacent mitered corner joint and drywall, as I will need to reinstate it when I move out. What needs to be done: Score the painted edges/mitered corner joint to break the paint bond. Carefully pry the single skirting board panel off the wall inside the alcove. Pull or flatten any remaining brad nails on the wall so the surface is smooth. Leave the removed timber piece intact for me to store. Tools required: Please bring your own utility knife, pry bar/trim puller and drywall protection materials. Located in Maroubra. Flexible with time, but looking to get this sorted as soon as possible. Thank you!

I need someone with the proper tools to drill my new MDF kitchen cabinet doors for concealed hinges. I have: 4 new MDF cabinet doors (15mm thick), already cut to the exact same size as the existing doors. The doors are not drilled yet. I'm looking for someone who has experience with cabinet making or kitchen joinery and can: recommend suitable concealed hinges (if needed), or work with the hinges I purchase; accurately drill the hinge cup holes and screw holes so the doors are ready to install. This is for a rental property, so I'm looking for a neat, professional result at a reasonable cost. Please let me know: if you can supply the hinges or if I should purchase them first; what tools you use; and your quote for drilling the 4 doors. you'll find attached the 4 old doors (the mdf new doors are the exact same size), and the type of hinges currently used. thank you very much

Knock down and remove decorative timber from walls. Measures 195cm in width. Brick walls are on either side. Timber appears to be glued on at some points. Will require finishing/be ready for painting. Timber removal preferred but not required.

I need a bi-fold /concertina door suitable for the laundry room. It’s external to the house but undercover on the deck. Need someone to measure source and install. I think weather treated MDF would be suitable ie don’t expect an overly expensive option.

1. Install 2 x bathroom vanities - floor standing 1000 wide. 2. Install laundry cabinets upper and lower - tall cabinet, sink cabinet and uppers above sink and washer, and 3. interiors of 2 Built in Robes 1.5 & 2 m wide, incl shelves, hanging and drawers. Remove existing cabinets and take to the tip. Install new cabinets. Plumber will be supplied.

The black laminate board needs to be cut from the top and removed. Pictures are attached for reference.

Build shelves in cupboard.

- Full sand back + stain + seal - Approx 54m² - Includes fixing scratches as much as possible (see close up pictures attached) - Experienced floor sander preferred

I’m looking to get a rough idea of pricing for a massage table/bed with a solid wood base, similar to the attached photos. ***If it's not too expensive, I'd like to get the massage table built*** ---- I’m working with a low budget, so I’m aiming for the most cost-effective option while still maintaining good quality. Ideally: • Simple, sturdy design • Minimal squeak/noise during use • Option for 4 legs instead of 6 if that helps reduce cost • Storage option only if it doesn’t significantly increase price or compromise function If possible without significantly increasing cost, I’d also be interested in: A design that can be easily dismantled (e.g. detachable or screw-in legs for easier transport/storage) At this stage, I’m just exploring options to see if this is viable, so even a rough ballpark estimate would be greatly appreciated. Please note I live near Brighton-Le-Sands. Pick up/drop off if your not too far is preferred. Thank you.

Remove and replace 21 drawer fronts and 2 cupboard fronts and 2 cover panels and attach handles

Hi, I need help installing a wall-mounted cabinet in my bathroom area. Cabinet is already assembled Needs to be securely fixed to the wall Wall type looks like (gyprock / tile / concrete) Please bring your own tools (drill, wall plugs, screws, level) Need it mounted straight and secure

Carpentry day rate. Specialising in internal fit out (skirting, doors etc. assisting lead carpenter

6 replacement kitchen top cupboard doors with bevelled mirror front glass on mdf with soft close blum hinges. No install 2 x 765*497 2 x 765*472 2 x 381*297